Updates documentation for the frdm_k64f, hexiwear_k64, and usb_kw24d512
boards to reflect that they now support a watchdog driver. Updates the
board yamls similarly for sanitycheck.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The frdm_k64f board document incorrectly listed spi signals on PTCD
pins, which don't exist. They should be on PTD pins.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
If the ftm driver is enabled, use an instance routed to the Arduino
header and configure the pinmux accordingly. Unlike the hexiwear_k64,
the pins routed to the RGB led cannot be muxed as ftm channels.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new variable to define which OpenSDA firmware is on the board,
and selects the default flash/debug scripts accordingly.
Sets the default to daplink since the flashing and debugging examples in
the board document were written to use pyocd.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables a usable adc driver instance based on the board design and
configures the pinmux to enable the SoC's PTB10 pin, which is routed to
the Arduino header A2 pin. Updates the board documentation to reflect
that the board now supports an adc driver.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
A couple of docs were created in previous PRs with board support
information common to a few boards. Move these to a new section
for "Board Support Tools". (I debated about hiding them completely
but decided it would still be useful to have these tool docs appear
in the table of contents, just not embedded with the supported boards
docs.)
Moved these board tools docs over to the doc/ folder and out of
boards/ and removed these pages from the navigation index.
JIRA: ZEP-2285
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The wiki directions indicate that this script should be used,
and openocd.sh doesn't even work. Switch to pyocd.sh by default.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Now that NXP boards support 'make flash' and 'make debug' via pyOCD and
Segger J-Link, update all the NXP board docs accordingly. Adds a new
generalized OpenSDA document so certain details don't have to be
repeated for every OpenSDA board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
More general spelling fixes, and cleaning up stray UTF-8 characters
such as curly-quotes, em- and en-dashes. Use replacement strings
for |reg| and |trade|.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Add basic PHY management sufficient to detect link up, link down and
auto negotiated link speed / duplex. The PHY driver is implemented as
a state machine that executed in the system work queue. The
implementation is non blocking, using the MII interrupt to capture the
completion of read and write events.
This PHY management should be fairly generic. In the future, it may be
beneficial to pull this code out as a standalone PHY driver for use
with other ethernet drivers.
JIRA: ZEP-1674
Change-Id: I3dcb5c14982ef4b40591fcf10d84840b8a2558e5
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Working Ethernet, and actually even successfully booting with Ethernet
enabled (and Ethernet is enabled by default on enabling networking)
so far requires a network cable attached.
Change-Id: I9c17e417f867942ddf085db9e8342e945aa07370
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Johann Fischer