Since bb590b5b6e, which enforces a more consistent ordering of
initialisation for devices, the SOC initialisation was happening after
GPIO initialisation. This caused interrupts to stop working on GPIO
input.
This patch fixes that by increasing the default GPIO initialisation
priority, so that it happens after SOC.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Remove the test clock out Kconfig from SoC level. Instead use
device tree PINCTRL entry with updated clock control driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add support for Microchip MEC15xx to the XEC clock control driver.
MEC15xx 32KHz clock support uses the same 32KHz source for both the
PLL and peripherals. MEC152x does not include the PCR clock monitor
present in MEC172x. MEC15xx and MEC172x support internal silicon
oscillator, parallel and single ended crystal inputs, and the
32KHZ_PIN input. MEC152x supports fall back to internal silicon
OSC when VTR and 32KHZ_PIN are turned off. Therefore in MEC152x the
internal silicon oscillator can only be disabled if using an external
32KHz which is always on. For MEC152x the driver will only use the
PLL source clock device tree value.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Remove a redundant symbol that was used as a proxy to enable CONFIG_PM.
If an application needs to enable PM, it should just enable PM subsystem
Kconfig options. Furthermore, there's no clue "SOC_POWER_MANAGEMENT" is
a Microchip specific option.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Uses the stats subsys to provide simple but useful debugging stats for
power management state changes and timing.
Removes the no longer needed PM_DEBUG config option
Replaces the use of PM_DEBUG for a test clock output pin for mec1501 and
adds in its place an SoC Kconfig option to enable it.
Adds a STATS_SET macro for assigning a value to a stat group field
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Use new KConfig switches to configure debug support.
Correct ADC configuration where all ADC pins are in ADC mode.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Currently JTAG debug is enabled by default.
In some designs is desirable to disable JTAG functionality.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Introduce switch to allow board configuration for VCI pins to
remain HW-controled depending on the design.
Currently pins are always configured as GPIOs which is not always
desirable.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Created MEC1501 deep and light sleep example for MCHP MEC1501.
Modifications were made to SoC, board, timer, and hello world
sample program. Power management split into SoC power
implementing the interface and device power for device specific
logic.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also replace some
config
prompt "foo"
bool/int
with the more common shorthand
config
bool/int "foo"
See the 'Style recommendations and shorthands' section in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add KConfig board support to match board jumper settings
Failing to update bank selection will affect GPIOs tied to VTR3
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Add a kernel timer driver for the MEC1501 32KHz RTOS timer.
This timer is a count down 32-bit counter clocked at a fixed
32768 Hz. It features one-shot, auto-reload, and halt count down
while the Cortex-M is halted by JTAG/SWD. This driver is based
on the new Intel local APIC driver. The driver was tuned for
accuracy at small sleep values. Added a work-around for RTOS
timer restart issue. RTOS timer driver requires board ticks per
second to be 32768 if tickless operation is configured.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Initial support for Microchip MEC1501 series is added to the tree.
Additional support for UART is also included. This SoC supports
two operational modes for interrupts (Direct and Aggregated). For
this commit, the direct capable interrupt are configured in direct
mode.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Ederson de Souza