The sensor is on the nrf9160_innblue22 not nrf9160_innblue21. This
causes CI build failures since there is no dts node for the sensor
on the nrf9160_innblue21 board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use DT_INST_FOREACH macro to combine code used for multiple instances.
Remove unnecessary Kconfig options for UART instances.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Adding port information for uart tx and rx pins in dts, so that it can
be more systematically retrieved in the uart driver.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Change DT_GPIO_GECKO_SWO_LOCATION to use new DT_INST and DT_PROP macros
and remove defining it in dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines. As part of this conversion we
remove the Kconfig options for per GPIO controller enables and instead
get that information from device tree. This means we now disable each
GPIO controller by default in the DTS and have each board dts enable the
GPIO controller ports it needs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
board support nrf9160_innblue22 includes the sensor in
nrf9160_innblue22_common.dts, explicit overlay can be removed
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
This commit adds the asynchronous UART API testing support on the SAM
R21 Xplained Pro board.
The SERCOM3 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM3 UART TX and RX pads are configured to be
internally connected; it is, however, still necessary to configure the
pinmux because the module pads are not connected until the pinmux is
configured.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Replace DT_ALIAS_GPIO_x_LABEL with DT_NODELABEL references to get the
device name for the gpio ports.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Tell GitHub linguist to ignore the `.pat` generated test pattern files
that are used by the CMSIS-DSP tests (and potentially others as well,
in the future).
This prevents GitHub from classifying them as "Max language" in the
language statistics.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Adding support for nRF9160 based InnBlue board V2.1. Supports both
Secure and Non-Secure configurations along with various sensors
(lis2dh12 / hts221) and devices(i2c / pwm).
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
Move the FPGA GPIO init to use the devicetree.h macros instead of
dts_fixup.h. This allows us to remove dts_fixup.h on mps2 based
platforms.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Although it is not clearly specified in the UART API, this function
is supposed to return 0 when the TX interrupt is disabled, regardless
of whether anything could fit into the TX buffer or not (this can be
concluded from looking at implementations of several samples and tests
present in the tree, also almost all UART drivers are implemented this
way).
The problem in the uart_nrfx_uarte driver case is that the flag that
allows generation of the TX interrupt is not cleared directly in the
uart_irq_tx_disable() function but this clearing is deferred to the
end of the current transmission, in case one is in progress, and hence
it is done in the interrupt handler. Consequently, when the interrupt
handler is not entered between calls to uart_irq_tx_disable() and
uart_irq_tx_ready() (e.g. when both functions are called in a loop
executed in the interrupt context), the latter may return an invalid
value.
Fix this problem by additionally checking if the TX interrupt was
requested to be disabled, not only if it is already disabled in
hardware.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Espi bus interrupts need to re-enable after espi reset to get
all espi bus and vw signal interrupts.
Signed-off-by: Venkataramana Kotakonda <venkataramana.kotakonda@intel.com>
Epsi slave need to respond with an OOB_RST_ACK for OOB_RST_WARN sent by
master during host reset. Enable interrupt for OOB_RST_WARN to receive
signal changes and respond with ACK.
Signed-off-by: Venkataramana Kotakonda <venkataramana.kotakonda@intel.com>
This default-y option allows continued use of the legacy devicetree
macros.
There are no functional changes yet, but when this is default n,
old-style DT code won't build. At that point, adding any of these will
be a fix to keep old-style code working:
- "CONFIG_LEGACY_DEVICETREE_MACROS=y" to prj.conf
- "-- -DCONFIG_LEGACY_DEVICETREE_MACROS=y" to the west build command
- "-DCONFIG_LEGACY_DEVICETREE_MACROS=y" to the cmake command
This option can be changed to default n in time for the Zephyr 2.3
release. That will provide users of Zephyr 2.2 with a smooth migration
path to the new devicetree.h API after 2.3 is released, which
nonetheless will alert them immediately that something is wrong due to
build errors.
Unfortunately, __DEPRECATED_MACRO is not sufficient in all cases as a
warning to users. This is because, at least in GCC, macros defined
using __DEPRECATED_MACRO cannot be used in preprocessor lines like
"#if DT_SOME_LEGACY_MACRO".
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
SPI1, which is used by the LoRa radio, has the following
configuration:
SCK: PB_3
MISO: PA_6
MOSI: PA_7
NSS: PA_15
Update the pinmux configuration and documentation to reflect this.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
The check of the SF_TXDATA_FULL flag is only done on the register
address and not on the actual register content.
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
Test is checking if alarm handler is executed at request time or later.
However, validation did not take into account wrapping of the counter.
Fixed by taking into account case where counter wraps.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Fixes test which did not take into account that counter may
wrap (nrf51 has 16bit timers) and was setting alarm to wrong
value. Error was not seen on platforms with higher top value.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Convert old DT defines of the form DT_ARM_SCC_BASE_ADDRESS to
DT_REG_ADDR(DT_INST(0, arm_scc)). This allows us to remove dts_fixup.h
on musca boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds the asynchronous UART API testing support on the SAM
D21 Xplained Pro board.
The SERCOM1 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM1 UART TX and RX pads are configured to be
internally connected.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
In conversion of nodelabels to match SoC docs, we missed a case in the
board dts files. However these delete-node commands are not needed as
we normally handle this via the 'status' property being disabled which
enet2 is by default in the SoC dtsi files. So we can safely just remove
the stale /delete-node/ eth1 lines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use instance macro's instead of dts_fixup.h based
macros. This moves us closer to removing both dts_fixup.h and per
instance Kconfig symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked adc_sam_afec driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. We also remove
defines in dts_fixup.h as they are no longer needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. We update one
sample app to use a nodelabel reference. We also remove defines in
dts_fixup.h as they are no longer needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In order to fix the line tracking of the TCP packet allocation
with the test protocol enabled, refactor tcp_pkt_alloc(),
so the line of the allocation can be tracked properly.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
The net_idx parameter has been removed from the Health Client
model APIs since it can be derived (by the stack) from the
app_idx parameter
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
According Mesh Profile 1.0.1. A application key shall
binding single network key. And Device key shall bind all
network key, and dev key only known by cfg_cli and node self,
only used by cfg_cli & cfg_srv.
Fixes: #21088
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
Fixes bug where the config client's net_key_status handler would attempt
to pull two key indexes from a message which only holds one.
Fixes#24601.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
The LwM2M stack would previously ignore all OPAQUE resources when
reading them. This meant that it was impossible to read them, even if
there was a custom read callback.
Signed-off-by: Göran Weinholt <goran.weinholt@endian.se>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-uart binding for dma to replace the rxdma and txdma
properties with proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a common header for SAM0 drivers to use to extract data from
devicetree. The initial set of macros are for get the MCLK A*MASK
register address for clock enablement and a set of macros for use with
DMA to get the channel and trigger source or 0xff if there is no dmas
property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the atmel,sam0-dmac binding under the dma binding dir and add
cell information for channel and trigger source. Update the associated
dtsi files to match these changes.
This is in prep of ATMEL SAM0 SERCOMM devices like UART, I2C, and SPI to
user proper 'dmas' property to specify the dma info to use.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the GCLK, MCLK, and PM clock controllers. Add bindings
and devicetree nodes associated with these clock controllers. Also add
clock references for the SERCOM peripheral set to allow those drivers
(i2c, spi, uart) to utilize this information.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds handling of the FLOAT_64BIT option when determining the ISA
flags as well as introduces a new Kconfig option to enable/disable
the hard-float calling convention.
Signed-off-by: Corey Wharton <coreyw7@fb.com>
Kumar Gala