These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update a couple of labels generated from DTS used directly (not through
dts_fixups) in TI CC2650 system initialization code and a few drivers
for this SoC.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Now that Cortex-M7 cache issues have been fixed in commits 828ae6b8 and
13972693, it is possible to safely enable the MPU on the STM32F7 SoC
series.
Note that the ITCM area is not mapped into an MPU region. This should
not be an issue for now, as Zephyr does not provide yet a way to
populate and use this area.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
STM32F103 micros starting from 64-pin (xE) packages upward have
available port G. This patch defines a dts binding for them.
Signed-off-by: Pavel Kral <pavel.kral@omsquare.com>
Provide CONFIG macros for clocks bits and bus properties in fixup
files and use them to simplify logic in uart devices instanciation
code
Fixes#10448
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We now place the linker directives for the SW ISR table
in the common linker scripts, instead of repeating it
everywhere.
The table will be placed in RAM if dynamic interrupts are
enabled.
A dedicated section is used, as this data must not move
in between build phases.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The information extracted from the device tree is now used to initialize
GPIO device instances. Up until now the GPIO device driver made no use
of this information. Actual instance creation is still controlled using
the Kconfig method. Missing GPIO device tree nodes were added in the
process for STM32L073, STM32F413 and STM32F373.
The information for gpio instance initialization has already been
present for supported STM32 SoCs but remained unused. Changes in the
device tree had no effect on GPIO functionality and was essentially
redundant. Using the device tree for hardware description seems
plausible and less painful than a myriad of defines in some SoC
description header.
The change was implemented under the assumption that current device
trees provide a correct description of the SoCs. Base register addresses
and RCC register bits were not explicitly checked for each device.
Manual tests were executed on:
- NUCLEO-F103RB
- STM32F429I-DISCO
- STM32F746G-DISCO
- NUCLEO-F767ZI
Manual tests consisted of blinky on different GPIOs and pins on each
board.
sanitycheck was executed for all STM32 based boards
Fixes: #10629
Signed-off-by: Martin Bertsche <martin72216@googlemail.com>
Add a linker script entry for embedding a GNA model at a
4KB page aligned address in .data section
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
The only difference between the F413xH and F413xG is flash memory size.
STMF413xH: 1536 Kbytes
STMF413xG: 1024 Kbytes
Signed-off-by: Benoit Leforestier <benoit.leforestier@gmail.com>
This patch adds a USB device driver for the USBHS device that can be
found on Atmel SAM E70 SoC family. Only the FIFO mode is supported
(as opposed to DMA). It supports LS, FS and HS modes, but defaults to
FS mode as Zephyr does not fully support HS mode yet.
Tested examples on an Atmel SMART SAM E70 Xplained Board:
* usb/cdc_acm
* usb/hid-mouse
* usb/mass
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add dts binding and info for TRNG device and enable basic support to
get the device name from DTS. We leave for now the base addresses
coming from the MCUX HAL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add dts binding and info for RNGA device and enable basic support to
get the device name from DTS. We leave for now the base addresses
coming from the MCUX HAL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert gpio_cc32xx driver over to using device tree. Added binding
files, updates to dts for various SoCs that use cc32xx.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The define NRF51822 has no in-tree users and is believed to have been
added by accident. The define NRF51 should be referenced in it's
place.
To avoid users accidentally referencing NRF51822 instead of NRF51, and
to avoid confusing users into believing that NRF51822 has semantics we
remove it.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The build script ext/hal/nordic/CMakeLists.txt manages the MDK
dependency. The MDK is not aware of Zephyr and uses it's own defines
to indicate what HW we are building for.
This commit moves these MDK-specific defines out of the 'soc' build
scripts and into the MDK build script where they belong.
This is expected to be a pure refactoring without side-effects.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Update the uart_miv driver to get params like name, addr, baud-rate,
clock freq from DTS generated defines. Fixup related board and soc code
as needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add minimal DTS support for the m2gl025_miv. The dts just has the core,
SoC, PLIC, and UART described. We still get memory related info from
Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The DTS changes introduced in 7ae220c845
changes the naming of GPIO related macros. This updates the usage
of previous macros via DTS fixup.
Fixes#10993
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Fix misspellings in Kconfig files that show up in the configuration
documentation (and make menuconfig screens).
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Adding watchdog driver for sam SoC. The current implemntation just
diables the watchdog on device boot.
This PR adds the following support for SAM3X, SAM4S and SAME70
1. Activate processor reset
2. Activate all reset
3. Generate interrupt on watchdog timer expiration.
Signed-off-by: Subramanian Meenakshi Sundaram <subbu147@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
XCC does not support the "-undef" flag so set NOSYSDEF_CFLAGS to
empty string to fix compile warning.
Also, XCC does not supply the macro __SIZEOF_LONG__ which breaks
the build. So define it.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove the auto-generated `handle_irq` label for the unneeded cases
to get rid of a compile warning.
Fixes#10801.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
When users are configuring nRF applications they are given the option
to enable the DesignWare I2C driver. But they should not be given this
option because nRF SoCs do not have DesignWare I2C HW.
This commit hides the driver by default by introducing the config
option HAS_I2C_DW.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This commit contributes a Kconfig symbol hierarchy which allows
the user to build Zephyr Secure and Non-Secure images on ARMv8-M
MCUs with support for Trusted Execution. However, the high-level
configuration structure is generic, thus, can be potentially
used for any platform that supports Trusted Execution.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This adds the necessary bits to support ASM2 with XCC
for Intel S1000 SoC. With ASM2 enabled, xcc is now
required to build for Intel S1000 SoC.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
(Previous patch set was reverted due to issue with priv_stack.
Resubmitting after fixing the faults caused by priv_stack.noinit
not at the end of RAM.)
This adds a linker flag and necessary changes to linker scripts
so that linker will warn about orphan sections.
Relates to #5534.
Fixes#10473, #10474, #10515.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The Cypress PSoC6 specifies some input sections in the startup
scripts. These sections (.heap, .stack, etc.) need to be placed
at correct location.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This allows the SoC to specify some additional linker script
fragments into the bss, data and read-only data sections.
For example, the Cypress PSOC6 has a few input sections that
must be put into bss and data sections. Without specifying
these in the linker script, they are consider orphan sections
and the placement is based on linker heuristic which is
arbitrary.
POSIX is not supported as the main linker script is
provided by the host system's binutils and we have no control
over it. Also, currently Xtensa SoCs have their own linker
scripts so there is no need to this feature.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Andrzej Głąbek