Enabled ENET ethernet port on Cortex-A Core for imx8mn EVK board.
Updated document for supported features.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Enabled ENET ethernet port on Cortex-A Core for imx8mm EVK board.
Updated suported featues in board document.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Currently imx8mm/n use pinctrl binding of nxp,imx8m-pinctrl.yaml which
is used for imx8mq series platforms, but imx8mm/n have different pinctrl
hardware module with imx8mq, so change imx8mm/n to use binding of
nxp,imx8mp-pinctrl.yaml as imx8mm, imx8mn and imx8mp have the same
pinctrl hardware module.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Add mfd_adp5585 and gpio_adp5585 driver. This driver enables ADP5585
as an GPIO expander.
This chip is used as an GPIO expander on i.MX93 EVK. GPIO pinctrl,
read/write and interrupt is supported.
Note that ADP5585 has 2 GPIO banks with 5 pins each. The driver combines
two group into a 16-bit port. Index 0~4 correspond to R0~R4 lines, index
8~12 correspond to C0~C4 lines. Index 5~7 is reserved unavailable.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
i.MX93 share similiar register layout with i.MX RT11xx. Change ccm driver
to align with i.MX RT11xx, and make it easier to enable other drivers.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
The labels used in chosen node are not defined in dtsi file.
They are defined on board level and also chosen is already set there to
proper values.
Signed-off-by: Franciszek Zdobylak <fzdobylak@antmicro.com>
Add i.MX93 Cortex-A Core support on Zephyr.
i.MX 93 applications processors deliver efficient machine learning
(ML) acceleration and advanced security with integrated EdgeLock
secure enclave to support energy-efficient edge computing.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
i.MX8M Nano LPDDR4 EVK board is based on NXP i.MX8M Nano
applications processor, composed of a quad Cortex®-A53 cluster
and a single Cortex®-M47 core.
Zephyr OS is ported to run on the Cortex®-A53 core.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
1. Enable all cpu cores in soc dts and disable unused core in board dts.
2. Use default irq priority for uart interrupt.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
The armv8 timer, arm gic, and arm gic-v3-its don't use or need the
devicetree label property. Update the dts bindings to not require it and
remove setting of the label property in dts files.
Signed-off-by: Kumar Gala <galak@kernel.org>
The ns16550 flags reg-shift property as optional. In case it is not
supplied, the ns16550 driver relies on a value defined in <soc.h>, or,
by default it takes 4 (shift by 2).
This patch adds the property to all ns16550 nodes, with the following
values:
- 2 if SoC did not have any custom value defined by
UART_REG_ADDR_INTERVAL (corresponds to 1 << 2 = 4)
- If SoC defined DEFAULT_REG_INTERVAL (snps_arc_iot/it8xxx2), use such
value (4=2, 2=1, 1=0).
These changes will allow simplifying the ns16550 driver.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add partial pin control support for the imx8mp. Since the UART driver is
not currently enabled, pin control cannot be tested on this platform.
Therefore, only the DTS definitions required to set the pinmux options
are present for this platform, and are not being applied (since
CONFIG_PINCTRL=n).
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add initial pin control support for the A53 core of the imx8mm. Since
the UART console driver is not currently enabled for this platform,
there is no way to test the full pin control enablement. Therefore,
CONFIG_PINCTRL is still not selected for this platform, although the
required DTS definitions and pin control headers are present.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
In order to bring consistency in-tree, migrate all dts code to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to zephyrproject-rtos#45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
rename IMX_CCM_UART_CLK to IMX_CCM_UART4_CLK and
IMX_CCM_UART2_CLK a53 dtsi.
This was missed in a previsous patch set.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
1. add a seperate 2 cores SMP board configuration to run in Jailhouse
inmate Cell, root Cell Linux will use Core0 and Core1, Zephyr will
run on Core2 and Core3.
2. Refine the code of dts, move SoC common dts nodes into dtsi fiel in
dts/arm64/nxp/ directory.
3. Add myself to be code owner of directory dts/arm64/nxp/.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Jiafei Pan