Update serial drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
We remove 'depend on' Kconfig for symbols that would be implied by
the devicetree node existing.
Signed-off-by: Kumar Gala <galak@kernel.org>
Reworked uart_sam driver to utilize new DT_INST macros as part of this
rework we also now get pin ctrl/mux configuration information from the
device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
SAMV71 uses same driver of SAME70 and this enables the feature. Since
driver is shared with other devices, it must be enabled conditionally
based on the number of instances. This avoid show invalid options for
devices with lower port count like SAM4S/SAM4E.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Implements interrupt driven UART for the serial driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Justin Watson <jwatson5@gmail.com>
The SAM4S, SAM3X, SAME70 all use the uart_sam.c serial
driver. This patch puts the configuration in DTS and
out of Kconfig. The SAME70 uses the USART as well.
USART DTS support for the SAME70 is also in this patch.
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Limit visibility of configurable TX pins to SAME70 series only.
Previously visibility of configurable SAME70 TX pins extended
to the full SAM family.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added serial (UART) driver for Atmel SAM MCU family.
Note:
- Error handling is not implemented
- The driver works only in polling mode, interrupt mode is
not implemented.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1959
Change-Id: I3e770fd1feb2ddf92cf405a9aa17be92eb32e19b
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Kumar Gala