This patch adds Beetle to the Watchdog test case.
Jira: ZEP-1300
Change-Id: I371ca2f89aaec8e07f45cfa04fc2618d009cf487
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Fixing a tiny build error found through sanitycheck.
Change-Id: Iee9a3ac135380ddf70e2902b532f6f28d417715c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Adds a fxos8700 sample application that uses the sensor data ready
trigger to periodically print accelerometer and magnetometer data.
Change-Id: I43fef6cd6090b58d8d0168a25558a3a05781ea5d
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This allows to fine tune TX stacks size depending on selected HCI
driver. If needed it can be used to tune for monitor too or other
logging mechanism used.
Change-Id: Ib501921da0b786e151083760d85ec58fe3c08b60
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Use BT_STACK_NOINIT for tx stack declaration. This makes sure stack
it properly alligned and account for k_thread overhead.
Change-Id: I704958fcc3ce02aba913f6eaee13ae50d2a81591
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
bt_enable_raw() needs to be called before spawning the tx thread,
otherwise there might be an HCI command processed from the UART
before the HCI driver has been opened and therefore initialized.
Change-Id: I050158bd48bebaf8fa2cf6b11efb54b531f70079
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
From stack_analyze function, used isr stack is 368 bytes
with the controller build, main stack is 288 bytes and idle
stack is 56 bytes. Hence, configuring sizes of 512, 512,
and 256 bytes for isr, main and idle stacks respectively.
Increased max connections from 16 to 20 utilizing the RAM
free from the reduced stack sizes.
Change-id: I67d073fd1893cafc53d36e89035a6fd931488a46
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Implement the 2 HCI commands that provide ECC public key
and shared secret generation:
- LE Read Local P-256 Public Key
- LE Generate DHKey
Jira: ZEP-1246
Change-Id: I79388bfdb9f2e28b9377b4bb6ee2caca25f33f3e
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
CC2520 is not embedded on an arduino_101, it is however possible to wire
one, and thus it requires to provide cc2520_configure_gpios() function.
This one, being common to a101 is found in samples/net/common.
Change-Id: I86f2734847edb3f6a968522afccc3099ed854d13
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Commit https://gerrit.zephyrproject.org/r/#/c/6971/ changed the
location of some include files, making compilation fail.
Change-Id: I43c124be28b55e550ef2204ca9faa7031665fb4a
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
This commit updates the dns client application to use the
new kernel API.
Change-Id: Ibf920532b02a1561bfb38f69e5dd994ab21574bc
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
* Moved networking code into subsys/net.
* Renamed net/yaip to net/ip at the same time.
* Fixed the tests/net to compile
* Fixed the Makefiles and Kconfig files in subsys/net
to use the new location of the IP stack
Change-Id: Ie45d9e8cb45a93fefdf969b20a81e3b1d3c16355
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Port the zperf network performance tool to native IP stack.
TCP support is missing from this version.
Change-Id: I2648e7d81014bb0cae8cf50854b0ae5f89a6567c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we cannot send a network packet, do not quit as that is
really not necessary here.
Change-Id: I7613d46bdbc849b75aaf0fc71c58beba810fd658
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the default board is qemu_x86, make sure there is similarly
named config file that can be used by default.
Change-Id: Ibc480d3b4eecc2601e3670c8da19be9c01833c36
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use by default a board specific config files for both
echo-server and echo-client sample applications.
This makes more sense than using the network technology specific
config file that was used earlier.
Change-Id: I155fc138f4b0ed1166f4e25267513afc3fb6fd76
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove legacy stack artifacts from the echo-server and echo-client
config files.
Change-Id: Icc591b9540495c4ee181517369b0df9bb91972bb
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This enables application debugging using qemu target:
export QEMU_EXTRA_FLAGS="-s -S"
make qemu
Was tested with echo_server
Change-Id: I1906dea2fbc5afe03b11729d2edb8f3629a629f8
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
As the native IP stack is now the default, there is no need
for corresponding Kconfig option.
Change-Id: I08e4992f540f928a2b7378e8803e634e38725348
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit removes the old MQTT and NATS publisher and subscriber
applications that were based on the uIP stack.
Change-Id: I7ba8e155e32ba0aa53c8dec1b6c0cc5170d70943
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit removes the legacy Contiki based uIP stack.
The new native IP stack must be used after this commit.
The commit also removes following things:
- legacy cc2520 driver
- legacy ethernet drivers
- legacy IP stack samples
and changes these things:
- disabled tests that only work for legacy IP stack
- select new IP stack by default
- enable random number generator by default as it is needed
by the new IP stack
Change-Id: I1229f9960a4c6654e9ccc6dac14a7efb9394e45d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
My IPv4 address was missing because of complex set of #ifdef's.
Change-Id: I6768587d3e104a57c10756bc43267f26068aa3cb
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Nbuf data size needs to be set to 128 bytes, specifically for
wpan sample.
Debug output kills timing, and thus can generate spurious failures on
reception, so limiting it to errors by default.
Change-Id: Ia918361d07369dacbe577e26855d7ef6ed865f7b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The used IPv6 or IPv4 address can be set in the config file.
This way one does not need to edit the source file to setup
the desired IP address.
Change-Id: Ic900bd4694481b4b035026ad0ba7b9280eb84e4a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Let the echo-server listen any configured IPv4 address
by default.
Change-Id: Ib83c5e069ae1e26615c37fa980bc4009b5a5e40c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If user has enabled DHCPv4 support, then do not try
to set static IPv4 address.
Change-Id: Ia359f578044d72b951f53c509c92c09d575207f0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we want to receive packets to multiple addresses, the solution is to
listen on the ANY address, and add the address to the interface in
question (already done).
Change-Id: I383cc1401f1236ee05bdb010252a9f9909aa15bd
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Before using the LED we must set the direction of the GPIO pin to
output, and the LED will turn on when that GPIO pin is 'low'. So, for
our purposes, the LED is active low.
Change-Id: If8e6ce05ff2f3ddb7b17a87b172a91f7276194a4
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
'board.h' includes the definition of LED0_GPIO_PORT and LED0_GPIO_PIN,
without this include the fallback was used, as if the board in question
didn't have any LEDs.
Change-Id: I78ebdb2e2ffc41dff5011dcf9e33e09d70950e81
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This adds a configuration profile allowing this example to run on a
Quark SE C1000 devboard.
Change-Id: Ic04fd30a91ed0a1fc8c3a3b3a6e397f0722f50b1
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Nbuf data size needs to be set to 128 bytes, specifically for wpan
sample.
Debug output kills timing, and thus can generate spurious failures on
reception, so limiting it to errors by default.
Change-Id: Ia0b8c904e0bc66a7922af4f317db623db6c51462
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This adds the required code to echo server so that it works with TCP as
well.
Change-Id: Ib45dd91a52a60ddb4d8f0ae11175ceb52199c398
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Including shell allows to execute some kernel commands and make sure
system is not crashed.
Change-Id: I6157229614655dc7e523f1cf0f84ee7c58d7a717
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Due to huge delays with DEBUG log level change it to INFO.
Change-Id: I81caf78fc6e9e064c2ed8e18caa99351028af62a
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
In a case transmit is failed send ack to the driver with zero sequence
number which is not used for valid seqs.
Change-Id: I1047de9ab5de636c5a8983f31376046757c4dc0c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Following replacing semaphore with timeout semaphore transmit may not
be finished returning error after which communication stalls. Allowing
3 retransmits solves the issue.
Change-Id: Ibad05c2eac43dd6bb0ed72aaf16a7a2ef4185067
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Having 1024 bytes was really unsufficient and creating a lot of weird
bugs everywhere.
Change-Id: Ib642744fa6dfc9f3a699a0dc2f0c1783dc6f87b2
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Vincenzo Frascino