The choice symbol LSM6DSL_EXT0_LIS2MDL was given a 'default' in
Kboards/arm/96b_argonkey/Kconfig.defconfig, but 'default' has no effect
on choice symbols, triggering a warning from Kconfiglib.
Instead of adding a default to the choice symbol, change the default of
the 'choice' itself by giving it name and adding the default in
Kconfig.defconfig.
This requires that we remove the default on the "base" definition of the
'choice', due to some messiness related to the Zephyr-specific
prefer-later-defaults behavior (see the 'Zephyr-specific Kconfig
behavior for defaults' section in the Board Porting Guide). Choices were
overlooked when that patch was added to the C tools, meaning choices
still prefer earlier defaults. The crux is that Kconfig.defconfig files
are included last.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These symbols were removed in commit 311e6b9e3e ("arch: arc: Use DTS
for all ARC SoCs"). The settings should come from DTS now.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Fixed the incorrect usage of CONFIG_FLASH in the defconfig.
This CONFIG_FLASH is used to enable the flash driver only.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Fixed the incorrect usage of CONFIG_FLASH in the defconfig.
This CONFIG_FLASH is used to enable the flash driver only.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Fixed the incorrect usage of CONFIG_FLASH in the defconfig.
This CONFIG_FLASH is used to enable the flash driver only.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
In preparation for introducing a warning.
Unquoted string defaults work through a quirk of Kconfig (undefined
symbols get their name as their string value), but look confusing. It's
done inconsistently now too.
Suggested by Kumar Gala.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The ST Nucleo L432KC board only has a reset switch and not user switch.
It has a single user LED connected to PB3, and called LD3 in the ST
documentation.
This patch fixes the corresponding device tree definition. At the same
time also it also fixes the documentation, where the name of the power
and user LEDs are swapped.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
TI literature site has links which are automatically updated to point
to the latest versions of pdf documents.
Use those instead of the hardcoded URLs.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Update board docs to reflect simpler method of flash/debug as
cc3220sf is now by default an XIP platform.
Include installation instructions for TI OpenOCD as a pre-requisite.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Previously, the cc3220sf platform could only be flashed using
TI UniFlash (or CCS) tools, requiring unique instructions.
Also, these procedures were not integrated with the standard Zephyr
build targets: 'flash', 'debug', 'debugserver'.
After installation of a TI OpenOCD v1.10 release, and other
one-time board setup, flashing and debugging can now be done
via OpenOCD/gdb, using the standard Zephyr build targets per
the Zephyr Application Development primer.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Previously, there was no easy command-line solution for loading
a Zephyr program to (internal) flash.
So, the default development method was to load via gdb/openocd
to SRAM and debug from there, thus making the cc3220sf platform
non-XIP (CONFIG_XIP=n) by default.
With new openocd v 1.10 updates from TI (git.ti.com/sdo-emu),
the image can now be flashed and debugged via gdb/openocd,
so the default will be changed to XIP (CONFIG_XIP=y).
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
As mentioned in
https://github.com/zephyrproject-rtos/zephyr/issues/7873, these Kconfig
symbols never existed. Remove the assignments to them.
Keep the dead code that's guarded by them for a while. I don't know if
this board is used.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Supposed to come from DTS. The Kconfig symbol was removed in commit
311e6b9e3e ("arch: arc: Use DTS for all ARC SoCs").
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
According to INTEL-SA-00115[1], Intel(r) Atom(tm) Processor E Series
are affected. All Minnowboards sports one of these processors.
[1]: https://goo.gl/CKyLQy
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Setting of CONFIG_HEAP_MEM_POOL_SIZE was done in the board defconfig
because open-amp was doing recursive builds and setting it the
defconfig made sure all builds were consistent. However, now that we
don't do recursive builds this will get properly picked by from the
sample specific conf file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The {FLASH,SRAM}_BASE_ADDRESS Kconfig symbols were removed in commit
311e6b9e3e ("arch: arc: Use DTS for all ARC SoCs"). These settings are
supposed to come from DTS now.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
USB IP is not directly available on disco_l475_iot1 and requires
some HW modifications to get it enabled.
Remove this USB pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
During transition from native to ll based clock_control
driver, a typo was introduced in PPL source selection flag.
Fix this.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The defconfig has CONFIG_SOC_MKL25Z=y, however CONFIG_SOC_MKL25Z doesn't
exist and should have been CONFIG_SOC_MKL25Z4, However its not
necessary to define this at all since it implied by the board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We had a comment related to the #endif for CONFIG_USB_DC_STM32 however
the comment said CONFIG_USB_DC_STM, so fix it to match the ifdef.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
CONFIG_BOARD_STM32_NUCLEO_{L432KC,L476RG} where set in the respective
board defconfig files, however these symbols don't exist. We can just
remove them from the defconfig as we'll get the board Kconfig symbol
defined by default when selecting that board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SPI_DW_INTERRUPT_SEPARATED_LINES symbol was removed and replaced by
SPI_DW_PORT_{0,1,2,3}_INTERRUPT_SINGLE_LINE in commit 423f0095c7
("drivers/spi: Specify options per-port on DW driver"), but an
assignment to it remains.
Remove the assignment and set SPI_DW_PORT_0_INTERRUPT_SINGLE_LINE to 'n'
instead. The Arduino has a single SPI port.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The Kconfig option TOOLCHAIN_VARIANT (not to be confused with
ZEPHYR_TOOLCHAIN_VARIANT) is a legacy configuration option that has
very few use-cases and can easily be dropped.
It's functionality is easily covered by CONFIG_X86_IAMCU and
ZEPHYR_TOOLCHAIN_VARIANT.
This commit removes all references of it from Zephyr.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The kl25z does not have the same spi hardware as the k64f and therefore
cannot use the same spi driver. Remove all references to spi for the
kl25z soc and frdm_kl25z board until we have a valid spi driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This commit adds a sample application using OpenAMP for remote procedure
calls on the LPCXpresso54114. It is adapted from the RPMsg-Lite sample
application added in PR #5960, and uses the IPM driver to provide
interprocessor interrupts.
Signed-off-by: Kristian Klomsten Skordal <kristian.skordal@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The current method of setting the openocd runner arguments works for
direct invocation from the command line, but the values that are
written to the CMake cache are not properly separated and are
difficult to parse, due to the fact that in several cases, option
values contain spaces.
Adjust these runner arguments so that the options and their values are
separate list items. This makes it possible to parse them accurately
from the CMake cache.
No functional changes.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
This target is already using the rbtree as part of CONFIG_USERSPACE,
so it incurs no code size overhead (actually it's a little smaller)
when using the scalable scheduler and waitq implementations.
The change also gets us test coverage of those choices on a default CI
target.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Use the named choices feature introduced by PR #6966
and configure LSM6DSL on ArgonKey board.
The two named choices introduced in LSM6DSL are:
- LSM6DSL_BUS_TYPE (default LSM6DSL_I2C)
- LSM6DSL_TRIGGER_MODE (default LSM6DSL_TRIGGER_NONE)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch adds dts support to lps22hb/hts221/vl53l0x
I2C sensors as well as lsm6dsl SPI sensor.
Since some info, like gpio for irq triggering or SPI bus
characteristics, may be provided through dts, they need
to be made optional in the LSM6DSL driver by usage of
macros like HAS_DTS_SPI_PINS or HAS_DTS_SPI_DEVICE.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit gets rid of the 'option env="ENV_VAR"' bounce symbols.
"$FOO" now expands directly to the value of the environment variable
FOO, instead of to the value of the Kconfig symbol FOO.
This change is likely to soon appear in the C tools as well. Those
'option env' symbols always seemed kinda pointless, and have broken
dependency handling due to forcing symbol evaluation during parsing,
before all the symbols have even been seen.
Compatibility with the C tools could be retained by naming all
'option env' symbols the same as the environment variable they
reference.
This commit also updated the Zephyr documentation to explain the new
behavior. It's relevant for $ZEPHYR_BASE and out-of-tree Kconfig
extensions.
Commit message from Kconfiglib (cbf32e29a130d)
==============================================
Make "$FOO" directly reference the environment variable $FOO in e.g.
'source' statements, instead of the symbol FOO. Use os.path.expandvars()
to expand strings (which preserves "$FOO" as-is if no environment
variable FOO exists).
This gets rid of the 'option env' "bounce" symbols, which are mostly
just spam and are buggy in the C tools (dependencies aren't always
respected, due to parsing and evaluation getting mixed up). The same
change will probably appear soon in the C tools as well.
Keep accepting 'option env' to preserve some backwards compatibility,
but ignore it when expanding strings. For compatibility with the C
tools, bounce symbols will need to be named the same as the environment
variables they reference (which is the case for the Linux kernel).
This is a compatibility break, so the major version will be bumped to 6
at the next release.
The main motivation for adding this now is to allow recording properties
on each MenuNode in a clean way. 'option env' symbols interact badly
with delayed dependency propagation.
Side note: I have a feeling that recording environment variable values
might be redundant to trigger rebuilds if sync_deps() is run at each
compile. It should detect all changes to symbol values due to
environment variables changing value.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add MCUX IPM sample application. It can be run on lpcxpresso54114
board at the moment.
We first build the slave core image out of the remote/ dir than the
primary core image is build which includes the slave core image.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add driver for MCUX mailbox which can be used for lpcxpresso54114
and other lpc and kinetis socs.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Add a board port to allow creation of "firmware" code that will run on
the slave core (Cortex-M0+).
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Updates documentation for the frdm_k64f, hexiwear_k64, and usb_kw24d512
boards to reflect that they now support a watchdog driver. Updates the
board yamls similarly for sanitycheck.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds the configuration, driver, and HAL changes required
to implement a MCUX based RTC driver for the NXP Kinetis KW41Z.
Signed-off-by: Andy Gross <agross@kernel.org>
This patch adds some DTS information to flesh out the NXP Kinetis
based RTC blocks. DTS fixups were added as well to match up the driver
usage to the DTS output.
Signed-off-by: Andy Gross <agross@kernel.org>
Be more obvious about the entropy_native_posix driver
being only a test utility which does not generate real
entropy.
Fixes: #6388
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Johann Fischer