This makes the SoC flash compatible with the common nonvolatile flash
YAML schema, and provides a write alignment. It mirrors work done on
nRF chips for the DFU subsystem.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add needed uart pinctrl configuration in pinmux node.
This is done thanks to <soc>-pinctrl.dtsi file matching
the <soc>.dtsi files
Populate stm32 f4 based boards dts files with references
to uart pinctrl nodes.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add "clocks" property on u(s)arts nodes on stm32 socs
Add a dt clocks binding file and rework clock_control
header file include new device tree binding file.
include/dt-bindings folder is introduced as dt-bindings
placeholder
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Remove memory node from skeleton dtsi and add device_type
property in every memory node in soc dtsi files
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This patch add the unit-address component to memory and flash
nodes. According to the DT specification, the unit-address of
a node must match the first address specified in the reg
property of the node.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This patch adds #address-cell, #size-cell properties to
cpus container node and device_type, reg properties to
cpu node.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The I2C controller nodes are the root of the I2C bus for that controller
and thus may have children nodes that represent the I2C devices on that
controller. Thus we need to specify the #address-cell & #size-cell
properties.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configure I2C using DT for the following STM32 boards:
disco_l475_iot1
nucleo_f401re
96b_carbon
olimexino_stm32
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This commit rework stm32f4 series dtsi files hierarchy.
stm32f4.dtsi was used as maximum common set of IP while it should
be considered as the minimum common subset.
Then, following on stm32f4 series hierarchy and inheritance rules,
stm32f4xxx.dtsi files are reworked to include the "parent" soc dtsi
file and then add own IPs to each SoC.
Change-Id: I394278c84a8ea38921f9f143f4fc52ef1c645d05
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In stm32 dtsi linux files, uart generic node name is serial.
Rename uart node names of stm32 dtsi files from uart@ to serial@
Change-Id: Iac5cbf7955f23cee520bc1790b0f324a17bfcf9e
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit fixes uart only nodes situation for stm32 devices.
st,stm32-uart yaml description is added to enable compilation
Change-Id: Iea78693bdfb90fbb09612b75685ed7ca0ccca6d6
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that we can utilize label in the device tree we can convert to
getting the device name for the STM32 UART out of the device tree
instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add missing UARTs from the main device tree. They are declared as
disabled and can be enabled individually by each board.
Change-Id: I0ec73c59b4c3c4ee56f12ae70f2d6cdbec14fe33
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
This commit provides dtsi files for available stm32 base boards.
For now only uart nodes and IRQ number are provided in order to
enable delivery of coherent material.
It also clears additional content from stm32f103xb.dtsi
Change-Id: I62d932c7f22b56e95bcd9566ce39e14a393dd640
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Marti Bolivar