* Rename DT_SRAM_SIZE to DT_DRAM_SIZE since that is more correct
* Remove mmio-sram compatible since that is not correct for DRAM.
* Rename node label from sram0 to dram0
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Previously, DTS specification of physical RAM bounds did not
correspond to the actual bounds of system RAM as the first
megabyte was being skipped.
There were reasons for this - the first 1MB on PC-like systems
is a no-man's-land of reserved memory regions, but we need DTS
to accurately capture physical memory bounds.
Instead, we introduce a config option which can apply an offset
to the beginning of physical memory, and apply this to the "RAM"
region defined in the linker scripts.
This also fixes a problem where an extra megabyte was being
added to the size of system RAM.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
For HPET devices, configure it with fixed delivery mode because HPET
timer interrupt is needed to fuel the scheduler for all CPUS.
For all other type of devices, like UART, I2C, GPIO, Ethernet, etc.
configure them as lowest priority delivery mode, in which IO APIC
delivers the interrupt to the processor core that is executing at the
lowest priority among all the processors listed in the specified
destination. In this case, the device drivers can avoid the trouble of
handling repeated interrupts delivered to all CPUS.
Signed-off-by: Zide Chen <zide.chen@intel.com>
Rework the atom/linker.ld to match how ia32/linker.ld works with regards
to how PHYS_LOAD_ADDR & PHYS_RAM_ADDR are set based on CONFIG_XIP and
from which DT_PHYS_{RAM,LOAD}_ADDR defines. We update the minnowboard
dts and atom.dtsi files to keep in sync with this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. We remove the
aliases and use nodelabel instead in the soc_gpio.h to determine the
label for the specific gpio controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The offset and the number of pins were swapped causing an error when a
64-position left shift was generated to calculate the pin mask.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This maps devicetree GPIO phandle arrays from the full controller pin
range to the sub-controllers required by Zephyr's limit of 32 pins per
controller device.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This breaks down the GPIO controller definition in DTS into
multiple entries. This allows these controllers to be
referenced by other DTS, and test board overlay files.
And also we can remove the entries in the dts fixup file.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There were complains about the unit-address and first reg
not matching. So update the DTS file to match.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This driver was still using CONFIG_* values to determine its address,
IRQ, etc. Add a binding for an "intel,hpet" device and migrate this
driver to devicetree.
Fixes: #18657
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
XIP support in x86 was something of a mess. This
patch does the following:
- Generic ia32 SOC no longer defines a "flash" region
as generic X86 devices don't have a microcontroller-
like concept of flash. The same has been done for apollo_lake.
- Generic ia32 and apollo_lake SOCs starts memory at 1MB.
- Generic ia32 SOC may optionally have CONFIG_XIP enabled.
The board definition must provide a flash region definition
that gets exposed as DT_PHYS_LOAD_ADDR.
- Fixed definitions for RAM/ROM source addresses in ia32's
linker.ld when XIP is turned off.
- Support for enabling XIP on apollo_lake SOC removed, there's
no use-case.
- acrn and gpmrb boards have flash and XIP related definitions
removed.
- qemu_x86 has a fake flash region added, immediately after system
RAM, for use when XIP is enabled. This used to be in the ia32 SOC.
However, the default for qemu_x86 is to now have XIP disabled.
- Fixed tests/kernel/xip to run by default on boards that enable
XIP by default, plus an additional test to exercise XIP on
qemu_x86 (which supports it but has XIP switched off by default)
The overall effect of this patch is to:
- Remove XIP configuration for SOC/boards where it does not make
any sense to have it
- Support testing XIP on qemu_x86 via tests/kernel/xip, but leave
it off by default for other tests, to ensure it doesn't bit-rot
and that the system works in both scenarios.
- XIP remains an available feature for boards that need it.
Fixes: #18956
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
After witnessing some strange errors with memory not being
what it should be, lifiting everything above 1MB has solved
it. The Zephyr binary was being loaded into memory containing
reserved regions, resulting in data corruption.
We still simulate XIP for testing purposes by setting up the
memory map as follows:
0x000000 - 0x0FFFFF : Non-present
0x100000 - 0x4FFFFF : "Flash" ROM region
0x500000 - 0x8FFFFF : "SRAM" RAM region
For a total of 9 megabytes of physical RAM used.
Fixes problems observed in some large tests when code coverage
is enabled (which increases the amount of RAM used even more).
Fixes: #17782
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
There doesn't seem to be any use of the virtualcom device in the code,
so lets remove it from the dts as it describes itself as a usb device
controller which it is not.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds a fixed clock node (representing clock driving
system bus). The added node is then referenced by peripherals requiring
information about driving clock frequency.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
Removed Quark D2000 SoC files and first-order related DT bindings.
A few config options have been moved from the CONFIG_* space to
the DT_* space, as they were defined in the D2000 Kconfig files
and "leaked" into the other Quark trees.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Since Kconfig is responsible for enabling/disabling devices at build,
the devices in dt are defaulted to status="ok" to keep the output in
generated_dts_board.conf the same across configurations and simplify
the board-level dts files.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Previous the register size was 1M, technically the there are only a
small handful of registers defined in the IOAPIC, so shrinking the size
to 4k, so its as most one page large.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The IOAPIC node shouldn't have been in the cpu container, especially
since the cpu container does:
#address-cells = <1>;
#size-cells = <0>;
So the reg field of the IOAPIC would be treated as 2 registers instead
of a register and size. Move IOAPIC node out of the CPU node fixes this
issue.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Apollo Lake devicetree is augmented with its 8 I2C interfaces.
The default number of dynamic IRQ stubs is increased to deal with
these new interfaces having IRQ vector detection at runtime.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The legacy PCI support in the DesignWare I2C driver is replaced with
the new PCIe support. The Intel Quark X1000 SoC and the galileo board
configurations are updated accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The UARTs are on the SoC, not the board, so move their descriptors
to the SoC-level. Also turn on auto IRQ detection as these are PCI-
attached and their IRQs are subject to change depending upon firmware
settings.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The GPIO driver for the Intel Apollo Lake has so many pins it has to
export ten devices to shoehorn its one device into the GPIO API. The
current implementation uses the shared IRQ driver because these
pseudodevices all share one IRQ. However, since the GPIO driver is
aware of all the possible interrupt sources, it's smaller and faster
(and not even messy) to handle it internally, so this patch eliminates
the dependency on the shared IRQ driver.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
A parallel PCI implementation ("pcie") is added with features for PCIe.
In particular, message-signaled interrupts (MSI) are supported, which
are essential to the use of any non-trivial PCIe device.
The NS16550 UART driver is modified to use pcie.
pcie is a complete replacement for the old PCI support ("pci"). It is
smaller, by an order of magnitude, and cleaner. Both pci and pcie can
(and do) coexist in the same builds, but the intent is to rework any
existing drivers that depend on pci and ultimately remove pci entirely.
This patch is large, but things in mirror are smaller than they appear.
Most of the modified files are configuration-related, and are changed
only slightly to accommodate the modified UART driver.
Deficiencies:
64-bit support is minimal. The code works fine with 64-bit capable
devices, but will not cooperate with MMIO regions (or MSI targets) that
have high bits set. This is not needed on any current boards, and is
unlikely to be needed in the future. Only superficial changes would
be required if we change our minds.
The method specifying PCI endpoints in devicetree is somewhat kludgey.
The "right" way would be to hang PCI devices off a topological tree;
while this would be more aesthetically pleasing, I don't think it's
worth the effort, given our non-standard use of devicetree.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
To avoid confusion, callbacks using ordinal pin numbers
is going to be reverted. So the driver has to be re-worked
to expose multiple devices so each device has 32 pins.
Also fixes#12765
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This allows the shared_irq driver to be configured by device tree.
With previous implementation, only the board configuration can
override the IRQ trigger, as the trigger config is a "choice" rather
than "config". With this patch, the driver can be fully configued at
the SoC level.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The CC2520 device is specific to the quark_se_c1000_devboard not the
intel curie SoC. Move the device node where it belongs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix the following dts warnings:
up_squared.dts_compiled: Warning (simple_bus_reg): /soc/gpio@0:
simple-bus unit address format error, expected "d0c50000"
up_squared.dts_compiled: Warning (simple_bus_reg): /soc/i2c@91528000:
simple-bus unit address format error, expected "9158000"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
patch adds the device binding for qmsi watchdog and device node
for socs which are using wdt qmsi driver.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert over x86 based boards to use device tree instead of board.h to
describe buttons & LEDs. There are a few boards that the button gpio
flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Makes the designware spi driver consistent with other spi drivers by
selecting HAS_DTS_SPI in the driver. This required adding spi nodes and
dts fixups to several arc and x86 socs, as well as enabling those nodes
in associated boards.
Also refactors the driver to use the base address, interrupt number, and
interrupt priority from dts.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
We get several warnings of the form:
Warning (unit_address_vs_reg): /soc/virtualcom@0:
node has a unit name, but no reg property
Fix by dropping the unit address from the node name.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /cpus/arcv2-intc@0:
node has a unit name, but no reg property
Fix by removing the unit address from the nodes. Some cases we had a
reg property and a unit address for such interrupt controllers, in those
cases remove both the reg & unit address in the node name.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_format): /soc/uart@000003f8:
unit name should not have leading 0s
Fix these by remove the leading 0s.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we have a common DT_SIZE_K macro use it instead of defining
__SIZE_K eveywhere. We also have DT_SIZE_M, so use that in a few
places as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds the SoC configuration for Apollo Lake. This is based
on the Atom configuration.
Origin: Original
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Fix the ns16550 uart driver and relevant SoCs accordingly.
All generic settings are now DTS based.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix the qmsi uart driver and relevant SoCs accordingly.
Also: using config for irq everwhere relevantly and not an hardcoded
value in the driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Get the name generated through dts as well.
Fix the rtc driver and relevant SoCs accordingly.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Kumar Gala