STM32WB HCI driver requires definition of 2 RAM regions to support
use of 3 shared memory sections: MAPPING_TABLE, MB_MEM1 and MB_MEM2.
In linker.ld, under conditions of HCI driver to be enabled,
define SRAM1 and SRAM2 based on input defined in stm32wb linker.
Then define the 3 sections MAPPING_TABLE, MB_MEM1 and MB_MEM
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Implement HCI driver for STM32WB. It allows host to controller.
It is based on ST library allowing communication over RAM shared
bewteen chip's C-M4 and C-M0 cores.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit removes redundant checks if the module
was already initialized.
The variable to mark the fact of initialization is
moved as a global module variable.
This allows creating more sophisticated unit tests
of the settings subsystem by giving a possibility to modify
the internal mark of the fact the system was initialized.
Signed-off-by: Radoslaw Koppel <radoslaw.koppel@nordicsemi.no>
Casting the tid variable from a void* into an u32_t just to cast it
back to a pointer is pointless. Let's make it a osThreadId variable
upfront and get rid of those casts around it. This also makes it
64-bit compatible.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
The Apollo Lake SoC no longer uses the legacy PCI driver, so remove
references and supporting code.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
While enabling specific I2C ports does indeed belong at the board
level Kconfig, the selection of driver (I2C_DW) is an SoC-level
choice, so it is moved accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Which UARTs are broken out from the SoC on a particular board is
board-specific; don't enable UARTs blindly in the SoC Kconfig.
Also, the default UART options are specified in the driver Kconfig, so
the same defaults specified in the SoC Kconfig are redundant. Removed.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Since Kconfig is responsible for enabling/disabling devices at build,
the devices in dt are defaulted to status="ok" to keep the output in
generated_dts_board.conf the same across configurations and simplify
the board-level dts files.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The UART references in dts_fixup.h are actually SoC-specific, not
board-specific, so they are moved. Since this leaves the board fixups
empty, the file is removed.
The SoC fixups are expanded to include the additional two ports that
are present on some revisions of the Apollo Lake.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Some firmwares (looking at you, slimbootloader) don't set the registers
in PCI configuration space to indicate the IRQ routing, so we remove
the check that verifies that the user and firmware agree on IRQ number.
Also eliminate the return value of pcie_irq_enable() since no one uses
it and we can't return a meaningful value any longer.
Signed-off-by: Charles Youse <charles.youse@intel.com>
Use a system clock tick of 0.1 sec when running on the NXP TWR-KE18F
development board.
Fixes#16234.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add SPI support to the NXP TWR-KE18F development board. There are no
onboard SPI devices, but both SPI busses are available on the primary
Tower System elevator connector.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Offloaded `fcntl` implementation should be available for all offloaded
implementations, not specific for TI. `socket_offload.c` is already
conditionally compiled based on `CONFIG_NET_SOCKETS_OFFLOAD` option, so
there should not be conflicts for non-offloaded interfaces.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Due to in-tree dependencies on Kconfig options defined in modules we end
up having warnings and errors when those modules are not part of the
manifest.
Users should be able to remove unwanted modules from their downstream
manifest and still build any board configurations.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This adds support for the async API for SAM0 SERCOM USARTs using
DMA to drive the device.
Tested on SAMD21 with a few trivial programs and with
tests/drivers/uart/uart_async_api.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Implement the get_status DMA API for the SAM0 DMA controller.
The busy field is set only when the selected channel is
actively transferring data (i.e. both enabled and selected by the
arbiter). The direction field is left unset, since that
information is not normally retained by the DMA controller.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Add a flag to the sequence structure that tells the driver it should
calibrate the ADC prior to initiating the sample.
Implement this for nRF SAADC. The implementation supports the
workarounds for PAN-86 and PAN-178.
Relates-to: issue #11922
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Allow user to set log level for UART console drivers. Add
log level option to UART pipe driver in order to see what it
is sending and receiving.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When removing a service using bt_gatt_service_unregister, its attributes
handles will keep their value which can cause a problem when adding the
service again to the GATT database.
When re-adding, the gatt_register routine is taking the last handle of
the GATT database to compare it with the handles of the service to be
added.
If a service has handles with a lower value than the last handle of
the database an error will occur.
If we add/remove/add the last service, no error will occur as its
handles are always greater than the last one of the database.
Instead of resetting the handles when unregistering a service and
reassign new ones we make sure that the handles of the services are
not in use in the GATT database in order to place the service back
where it used to be.
Signed-off-by: Arthur Crepin-Leblond <arthur.crepin@proglove.de>
This enables the ROM bootloader on the CC13x2 / CC26x2 LaunchPad
development boards. The bootloader can be started by holding BTN-1
during reset. This can be useful during development to recover a board
if DAPs get disabled.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Several customer configuration (CCFG) settings are useful for
development and deployment. This commit adds support for setting CCFG
values via Kconfig. It follows TI's recommendation of setting CCFG
values and then including the TI provided CCFG. This commit includes
support for enabling the ROM bootloader and additional settings can be
added as needed.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Erwan Gouriou