We shall not enable by default a system timer in ARM
platforms, namely the SysTick, the Nordic, or the SAM0
RTC timer, simply by assessing the hardware capabilities
(e.g. by conditioning on CPU_CORTEX_M_HAS_SYSTICK).
Instead, now, all ARM platforms needs to explicitly set
their system timer module. Note that this has already
been the case for ca 80% of the ARM platforms.
This clean-up allows us to decouple HW capabilities from
system configuration (for example, Nordic platforms may
enable option CPU_CORTEX_M_HAS_SYSTICK, and still use
the platform-specific RTC timer for system timing).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Update nucleo_f401re to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- disable I2C and PWM by default
- update yaml
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The STM32_ARM_MPU_ENABLE option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the STM32_ARM_MPU_ENABLE option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
We can use the chosen property "zephyr,console" to determine what uart
should be used as the console and find its name to generate a define for
CONFIG_UART_CONSOLE_ON_DEV_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all ARM platforms have a device tree we can move selecting of
HAS_DTS up and remove any !HAS_DTS cases, as well as setting in all the
defconfigs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commits align CONFIG_ factor names between stm32f4 and stm32l4
series to enable code factorization such as use of Q_DIVISOR.
Though, it does not concatenate kconfig sections as we might use
a bit of time to see what is needed in this regard
Change-Id: Ia603406d53949abf5675b801a5448397d5ab8462
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following activation of stm32 common clock driver for stm32f4 series
remove references to stm32f4 specific driver.
Change-Id: I372a0ea046007bcb34944d6b2b8880077583b1d3
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit provides CONFIG_ definitions to support
LL based clock driver on stm32f4 boards:
96b_carbon
nucleo_f401re
nucleo_f411re
This commit sticks to clock configurations previously defined.
Two changes to notice:
-HSE clock value should now be defined
-Prescaler values required as "1" should now be set to "1" instead
of "0".
Change-Id: I003bd226f198217d5e266e11fe37094773c1c62c
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds MPU support to the ST nucleo_f401re board based on
STM32F401XE.
Change-Id: I5e8042c1f964827980b974a565a4d4666eeccf3b
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Converted over all STM32F4 based boards to use device tree and removed
associated bits that now come from the device tree for STM32F4.
Boards that are now using devicetree:
* 96b_carbon
* nucleo f401re
* nucleo f411re
Change-Id: Ibe197ca0a3f5ad78d594485a578d986403cc824a
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There was a misalignment between Zephyr UART device numbering and
SoC UART IP. Device "UART_1" was mapped to IP USART_2, which could
be confusing for user.
This commit allows to align "UART_1" to IP USART_1.
Change is propagated to all STM32F103RB/STM32F401RE based boards and
respective pinmux drivers
Change-Id: Ia8099dfeec7b9c0c686c2a58ccb4dbb1a55b6537
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32Cube uses SoC defines made to reflect HW heterogeneity that
should be taken into account by SW.
Aim of this commit is to adapt values used by Zephyr to the same
diversity. This will help create new SoC values only when justified
by a real hardware difference that should be taken into account
by software.
For instance, for SoC stm32f401re following define is used:
*STM32F401xE
Which means:
*Same SW could be used on STM32F401RE and STM32F401CE:
same CONFIG_SOC could be used
*Different SW should be used on STMF401RE and STM32F401RC:
different CONFIG_SOC should be used
This change focuses on stm32f4xx series.
Change-Id: I56ff4d1815d09747cf722385532eb2dcbdf37b44
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move common config options one level up to try to simplify the per-board
defconfig
Change-Id: I3d80fa494050634d0f877af2015b01b85df20d1d
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Ioannis Glaropoulos