This patch addresses the following issues:
* Aligns the Kconfig code style with Zephyr projects requirements.
* Removes redundant "depends on" from Kconfig.
* Adds static to the containing file scope declarations.
Change-Id: Idaaa0d705a31bc69cdf7e576e303f581d3d0bd5f
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch addresses the following issues:
* Aligns the Kconfig code style with Zephyr projects requirements.
* Removes redundant "depends on" from Kconfig.
* Adds static to the containing file scope declarations.
Change-Id: I14651826724c014cc71d62ab6cab03c668c578c0
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch addresses the following issues:
* Aligns the Kconfig code style with Zephyr projects requirements.
* Removes redundant "depends on" from Kconfig.
* Adds static to the containing file scope declarations.
Change-Id: I6d48d2eaf6ffd5fa28b37e1d3ca2d467705110f3
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch addresses the following issues:
* Aligns the Kconfig code style with Zephyr projects requirements.
* Removes redundant "depends on" from Kconfig.
Change-Id: Ic9e2fd935417fa40127bddeba4660109332087ff
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
In ST CMSIS files, FLASH_BASE does not mean base address of FLASH register
Instead FLASH_R_BASE is used.
stm32f1 clock control driver is updated to be compatible with this naming.
Change-Id: Ic4fb49c60c392e15fd12c69266baf4c686bd343b
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Based on the STM32F10x driver. Removing old code as we need to use the
bus number when dealing with 4 possible peripherals.
Change-Id: Id0263aa008e9b039ff9a00339e5622e289ffdf99
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Integrating the IRQ definitions for both nRF51 and nRF52, and defining
the set of IRQ values that are common to both.
Also switch the controller, uart and clock drivers to use the common
header definitions.
Change-Id: Id6816d7a97720896cfe4df83656fb8b1f8fb01fa
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
In the Nordic Semiconductor's nRF5x series SoC clock control
system can source the system clocks from a range of internal or
external high and low frequency oscillators and distribute them
to modules based upon a module’s individual requirements.
In this commit the implementation adds support for 16MHz
peripheral clock, 32.768 kHz RC oscillator, and 32.768 kHz
crystal oscillator clock sources.
16MHz peripheral clock is required to use the 2.4GHz Radio
peripheral. 32.768 kHz RC or crystal oscillator clock source
is required to use the real time counter peripheral.
Jira: ZEP-896
Change-id: I1a1e22322a5a26b587f3e27bb979e6296987ac1c
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Clock control drivers are now using new system log macros. also update
the Kconfig variable to be a level rather than a bool.
JIRA: ZEP-311
Change-Id: Ia64e79e4e083df580861f64c661f8dbaa8a3985d
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Convert leading whitespace into tabs in Kconfig files. Also replaced
double spaces between config and <prompt>.
Change-Id: I341c718ecf4143529b477c239bbde88e18f37062
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use SOC_SERIES_* for naming SoCs with similar features and architectures
with the goal of code reuse. The Series in the config variable should avoid
name collisions and clearly denote the relationships within an SoC family.
Change-Id: I7a98542f96b5d5dc3acc23782c4d45f98cceb599
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Most of the SoC and board Kconfig use the same values for
driver initialization priorities. So refactor them, and
discard duplicate ones.
The shared IRQ init priority was changed so that the kernel
default init and device init priorities can be standardized
across all SoC/boards. Same goes for DesignWare SPI driver.
This also changes the UART_CONSOLE_PRIORITY and
IPM_CONSOLE_PRIORITY to UART_CONSOLE_INIT_PRIORITY and
IPM_CONSOLE_INIT_PRIORITY, to standardize across all drivers.
Note that this does not take away the ability to override
those values. This just provides reasonable defaults such
that there is virtually no need to override.
Change-Id: Ibbd95d802c637df06f9a2fd48763ee1e6f4ff627
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add support for use of HSE (incorrectly named PREDIV1)as input of PLL,
along with HSE bypass for stabilized external clock, and XTPRE
prescaler. Update PLL handling so that we do not unnecessarily enable
PLL clocks, instead enabling only the clocks sources that are required
as per user's configuration.
This change allows higher SYSCLK clock values, up to 72MHz.
Change-Id: Ia7c2be3ce11ac0de2efa664b20e7ab5fddd57a51
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Moves the kconfig options for STM32F10X clock control driver
into its own submenu.
Change-Id: I9ef658defe85feab3dfdb3e329710cb48bbffd86
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
() Moves the Quark SE clock control into its submenu.
() Fixes the dependencies in the SoC default Kconfig
so the options are not displayed out of place in
menuconfig.
Change-Id: Ifdf06242be8ceed03c2c657c942875a5a7f2750e
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This patch replaces all occurences of the macro DEV_OK by the actual
value 0 at the driver level. So this patch touch the files under
drivers/, include/ and samples/drivers/.
This patch is part of the effort to transition from DEV_* codes to
errno.h codes.
Change-Id: I69980ecb9755f2fb026de5668ae9c21a4ae62d1e
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
The patch adds a driver for STM32F10x series RCC (Reset and Clock
Control) subsystem.
The module is primarily responsible for setting up of MCU's clock
tree. In particular the driver sets up SYSCLK, PLL (with source
configuration), AHB prescaler, and APB1/APB2 prescalers. As part of this
functionality, the subsystem can enable/disable clock signal for
particular peripherals, thus reducing the power consumption of the MCU.
The driver implements clock control driver API. However, subsystem IDs
being HW specific are exposed in driver public header that must be
included by callers. The driver registers a single device using a common
name STM32_CLOCK_CONTROL_NAME. The device is initialized at
the PRIMARY level with priority 1. This allows the initialization to
take place right after SoC initialization routine.
The driver depends on selection of SOC_STM32F1X config option and is MCU
specific.
Change-Id: I8bea5db20726a24bce7b7ffe0b95de543240429a
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Extend the public API of clock_control driver with a function for
querying of clock rate driving given peripheral. This is useful when the
driver must calculate or configurae values that depend on the rate of
clock driving this subsystem.
A baud rate setting of UART port is an example of such operation. To
configure a particular baud rate the driver may need to set the internal
counters of UART port, where the actual value will depend on the clock
rate for this peripheral.
The implementation returns DEV_NO_SUPPORT for clock_control drivers that
do not implement such functionality.
Change-Id: I4e7ec96cd3678a4bb1ff289b0247488289310f2d
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Move quark_se clock control entries to separate file. This will help to
keep things organized once we add more clock control drivers.
Change-Id: Id8f4a94189ab5bbba9b6552777549cf426d79273
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Fix dependencies for external and sensor clock device names in
clock_control Kconfig.
Change-Id: I708f025cf3ce97bcd003754fb5b395712d203107
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
This is the last step before obsoleting DEVICE_DEFINE() and
DEVICE_INIT_CONFIG_DEFINE().
Change-Id: Ica4257662969048083ab9839872b4b437b8b351b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_DEFINE() so that it fits in the 'device' namespace.
Change-Id: I3af3a39cf9154359b31d22729d0db9f710cd202b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_INIT_CONFIG_DEFINE(), because (a) it was not fitting
in any namespace and (b) it is not used to declare, but rather define a
object.
Change-Id: I1da5822f06b85a9fb024b5b184afd0ccc01012ec
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Change terminology and use SoC instead of platform. An SoC provides
features and default configurations available with an SoC. A board
implements the SoC and adds more features and IP block specific to the
board to extend the SoC functionality such as sensors and debugging
features.
Change-Id: I15e8d78a6d4ecd5cfb3bc25ced9ba77e5ea1122f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Put initialization priorities as device driver Kconfig
parameter.
Initialization priority value for each platform is defined
in the platform Kconfig file.
Drivers and platform code use SYS_DEFINE_DEVICE to add
and initialization function.
Change-Id: I2f4f3c7370dac02408a1b50a0a1bade8b427a282
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Quark SE provides various clock controllers through its SCSS block.
Peripheral, external, sensor, and others.
This current drivers provides only the clock gating capability, for
peripheral, external and sensor. But it could support divider and more
other features once defined in the generic API.
Note: such clock has _nothing_ to do with a Real Time Clock (RTC).
An RTC provide clock timing like a watch would do. Here the clock
controller is about circuit clocking.
Change-Id: I1a365ae730dfc6be7686271f7fbb693e64a6ff6f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Tomasz Bursztyka