Move to CMake 3.20.0.
At the Toolchain WG it was decided to move to CMake 3.20.0.
The main reason for increasing CMake version is better toolchain
support.
Better toolchain support is added in the following CMake versions:
- armclang, CMake 3.15
- Intel oneAPI, CMake 3.20
- IAR, CMake 3.15 and 3.20
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
CONFIG_DEBUG_OPTIMIZATIONS should not be enabled by default in
prj.conf for tests or samples. Remove it from a few places that it
is.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the code responsible for aligning the flash write by writing fill
values - from stream_flash_buffered_write to flash_sync. This avoids
having to correct buf_bytes/buf_written after the write and thus
simplifies error handling.
This commit also fixes an issue where the write length passed to the
callback in flash_sync includes the fill length.
Signed-off-by: Jonathan Nilsen <Jonathan.Nilsen@nordicsemi.no>
Add additional API to stream_flash that can be used to make
stream write progress persistent using the settings subsystem.
This functionality makes it possible to resume a write operation
after it was interrupted, e.g. by power loss.
Signed-off-by: Jonathan Nilsen <Jonathan.Nilsen@nordicsemi.no>
The stream_flash_buffered_write, when invoked to do flush write, will
attempt to write the tail bytes from the buffer, filling the required
minimal write block size with erase value bytes; after write it rewinds
the buffer offset, bytes_written, by number of the "filler bytes".
Doe to lack of return code processing from flash_sync call, two things
would happen to context in case of failure:
1) the ctx->bytes_written would be rewind pass the value it had before
function call as it gets decremented by "filler bytes" even if write
failed;
2) the ctx->buf_bytes offset would be accounting for added "filler
bytes" which should not be counted as data in buffer.
Proper processing of return code has been added to remove effects
described above.
Unit tests have been expended to cover the scenarios.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The flash_sync function is able to call, if specified, write
verification callback to check whether data flash has been correctly
written to a flash. Part of that procedure is to read date back of
the flash and call the verification callback on the buffer;
in case if the read would fail, the flash_sync would return,
with an error code, without updating stream_flash_ctx.
The same logic should be applied to failed verification, but, due to
missing return, the stream_flash_ctx gets updated with probably
incorrectly written bytes added to total bytes_written and buf_bytes,
representing number of bytes awaiting in buffer, being zeroed.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The stream_flash_erase_page would update stream_flash_ctx member
last_erased_page_start_offset, to page offset it attempted to erase,
even if such operation failed.
The commit changes this behaviour so that in case of failure the
last_erased_page_start_offset would still hold previously, successfully,
erase page offset.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Added flash_area_erased_val() function for get value of erased
byte of memory which is under flash area.
This function already exist in MCUBoot and zephyr dfu subsystem
which makes simultaneous usage of both impossible.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add SHA-256 flash integrity method. It reads flash data from a
device giving an offset creating a SHA-256 hash to be compared
with a reference. On sucess match, zero is returned, otherwise
a negative errno value.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is done to support the idiomatic way of performing flush
operations, where the caller might not have access to the proper data
pointer. Also, there is no reason why reading from address 0 should
not be allowed.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
... because it is (required).
This makes a difference when building with CMake and forgetting
ZEPHYR_BASE or not registering Zephyr in the CMake package registry.
In this particular case, REQUIRED turns this harmless looking log
statement:
-- Could NOT find Zephyr (missing: Zephyr_DIR)
-- The C compiler identification is GNU 9.3.0
-- The CXX compiler identification is GNU 9.3.0
-- Check for working C compiler: /usr/bin/cc
-- ...
-- ...
-- ...
-- Detecting CXX compile features
-- Detecting CXX compile features - done
CMake Error at CMakeLists.txt:8 (target_sources):
Cannot specify sources for target "app" which is not built by
this project.
... into this louder, clearer, faster and (last but not least) final
error:
CMake Error at CMakeLists.txt:5 (find_package):
Could not find a package configuration file provided by "Zephyr" with
any of the following names:
ZephyrConfig.cmake
zephyr-config.cmake
Add the installation prefix of "Zephyr" to CMAKE_PREFIX_PATH or set
"Zephyr_DIR" to a directory containing one of the above files. If
"Zephyr" provides a separate development package or SDK, be sure it
has been installed.
-- Configuring incomplete, errors occurred!
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Added test for check proper service of flush-write when buffer
contains unaligned amount of data.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Convert with a combo of scripts and by hand fixups:
git grep -l DT_FLASH_AREA_.*_ID | \
xargs sed -i -r 's/DT_FLASH_AREA_(.*)_ID/FLASH_AREA_ID(\L\1)/'
git grep -l DT_FLASH_AREA_.*_OFFSET | \
xargs sed -i -r 's/DT_FLASH_AREA_(.*)_OFFSET/FLASH_AREA_OFFSET(\L\1)/'
git grep -l DT_FLASH_AREA_.*_SIZE | \
xargs sed -i -r 's/DT_FLASH_AREA_(.*)_SIZE/FLASH_AREA_SIZE(\L\1)/'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This library supports stream writes to flash with
optinal progressive erase.
This module is a direct copy of the functionality found in
subsys/dfu/img_util/flash_img.c
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
Replace DT_FLASH_DEV_NAME with DT_CHOSEN_ZEPHYR_FLASH_CONTROLLER_LABEL.
We now set zephyr,flash-controller in the chosen node of the device
tree to the flash controller device.
NOTE: For a SoCs with on die flash, this points to the controller and
not the 'soc-nv-flash' node. Typically the controller is the
parent of the 'soc-nv-flash' node).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The board name for the nRF52 DK, so far known as nrf52_pca10040, is
renamed to nrf52dk_nrf52832. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to
match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Using find_package to locate Zephyr.
Old behavior was to use $ENV{ZEPHYR_BASE} for inclusion of boiler plate
code.
Whenever an automatic run of CMake happend by the build system / IDE
then it was required that ZEPHYR_BASE was defined.
Using ZEPHYR_BASE only to locate the Zephyr package allows CMake to
cache the base variable and thus allowing subsequent invocation even
if ZEPHYR_BASE is not set in the environment.
It also removes the risk of strange build results if a user switchs
between different Zephyr based project folders and forgetting to reset
ZEPHYR_BASE before running ninja / make.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
We rename the nRF51 Dev Kit board target (nrf51_pca10028)
to nrf51dk_nrf51422. We update all associated references
in the supportive documentation and all nRF51-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The seasonal overhaul of test identifiers aligning the terms being used
and creating a structure. This is hopefully the last time we do this,
plan is to document the identifiers and enforce syntax.
The end-goal is to be able to generate a testsuite description from the
existing tests and sync it frequently with the testsuite in Testrail.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move flash.h to drivers/flash.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move flash_map.h to storage/flash_map.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
On boards that have the arm or nxp mpu, configure the mpu to allow flash
writes. Otherwise this test will fail with an mpu fault.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
After addition of flash_map auto-generation it is needed to
use generated flas_area name instead of hard-code.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move to latest cmake version with many bug fixes and enhancements.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
When using an IDE (e.g. Eclipse, Qt Creator), the project name gets
displayed. This greatly simplifies the navigation between projects when
having many of them open at the same time. Naming every project "NONE"
defeats this functionality.
This patch tries to use sensible project names while not duplicating
too much of what is already represented in the path. This is done by
using the name of the directory the relevant CMakeLists.txt file is
stored in. To ensure unique project names in the samples (and again, in
the tests folder) folder, small manual adjustments have been done.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Prepend the text 'cmake_minimum_required(VERSION 3.8.2)' into the
application and test build scripts.
Modern versions of CMake will spam users with a deprecation warning
when the toplevel CMakeLists.txt does not specify a CMake
version. This is documented in bug #8355.
To resolve this we include a cmake_minimum_required() line into the
toplevel build scripts. Additionally, cmake_minimum_required is
invoked from within boilerplate.cmake. The highest version will be
enforced.
This patch allows us to afterwards change CMake policy CMP000 from OLD
to NEW which in turn finally rids us of the verbose warning.
The extra boilerplate is considered more acceptable than the verbosity
of the CMP0000 policy.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
It shouldn't be necessary to disable the mpu for this test. Enable
CONFIG_MPU_ALLOW_FLASH_WRITE=y instead.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The flash API requires write protection to be disabled before erasing
the flash. It appears that the nordic platforms for which this test was
originally implemented do not enforce the requirement to disable write
protection. The mcux flash driver, however, does enforce the
requirement, so fix the test to make it work on kinetis platforms.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
With upcoming ICs that are not in the nRF5x family, rename the flash
driver and all its dependencies from nrf5 to nrf.
Should also fix the issue introduced by f49150cab6 which broke the
assignment of the flash device due to a partial rename.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Torsten Rasmussen