Add SPI sub-driver for sensor system.
Use SPI irq number definitions already in Zephyr header file.
Origin: Original
Change-Id: I215db3acc535093dd75c0817cbe5af77e6e76e16
Signed-off-by: Baohong Liu baohong.liu@intel.com
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Attributes should have stored their own attribute handle after
registering service. Handle values are assigned to attributes after
registering service and stack has to copy them.
Fixes:
GATT TC_GAD_SR_BV_03_C PASS
Change-Id: I8463340960d663161d0f7990390e60f06a1c7259
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@tieto.com>
This enable checking for errors and automatically print help string:
btshell> connect
connect <address: XX:XX:XX:XX:XX:XX> <address type: (public)>
Change-Id: Ie097ecddb72ab15bf6192e310d0bd839bfd251d5
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove the CONFIG_SENSOR_DEBUG as it is no longer needed since switching
to SYS_LOG_* in the sensor susbsystem.
Also, use __ASSERT where CONFIG_SENSOR_DEBUG was used to validate
function parameters.
Change-Id: I80ed7209abfb92220fa229d246c5b3a43b887e32
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
I've found many problems with the SPI driver and this repairs many of them.
The baud rate divisor was being derived from the CPU clock. But, some
targets may have a seperate clock attached to SPI. If the soc.h file
defines the symbol SPI_DW_SPI_CLOCK, it will use this instead
of CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC for the baud rate calculation.
completed() had a mistake where it would terminate the SPI transaction
too early, well before the tx data has cleared the FIFO. I found I couldn't
drive an OLED display correctly because completed() was wrong.
The repair is to now consider a new flag called spi->last_tx,
which will be set after the TX interrupt occurs with nothing to send any
longer. There is also a while loop added to SPIN until BUSY drops.
Another improvement is that push_data will NOT consider RX fifo size
if there is no RX going on. The calculation here when RX is going on
could go negative. I've added a check for that and prevent TX handling
if RX buffer is full. I think that is the intention -- to deal with RX first
if its fifos are more full.
In spi_dw_transceive, if we are only doing spi_write w/o reading,
don't enable RX interrupts at all. The OLED I'm working with failed
to have a pull-up on MISO SPI signal. As a result, a huge number of
garbage RX events arrive, and the interrupt handler finds there is
no rx buffer, so it tosses the data. But this is a waist of realtime.
It seems WRONG to enable RX interrupts if its something your not using,
so software can GATE these spurious events in this way.
With these changes, SPI can be used much more reliably, with FIFOs
that are deeper, and SPI devices that only require TX.
Change-Id: I0fe0745f2381c61c8a19ce086496b422a32a30a5
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
This checks if the command string is either NULL or empty since in these
cases there shouldn't be necessary to do any lookup.
Change-Id: I27e6d5b07ab4000cce93a4d1f7952e3c57672657
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Contrary to strcmp strncmp does not match the entire string only the
initial bytes passed as len thus causing a prefix match not a exact
match logic.
Change-Id: I85f96beb2249223f44c81c4efd6bd01bf2033a2e
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Firmware does not filter by UUID so we need to do this ourselves.
Change-Id: I55808836369194fbc5ea7c35db2c72fcda75e4eb
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This adds a optional help string to the command table which is printed
when user enters > help <command>.
Change-Id: Id3a8995bb6c4ff6b009418e31968c0677e6e4921
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When using the Synopsys DesignWare Synchronous Serial Interface (SSI),
the FIFO depth can vary from 2-256, depending upon how this module is built.
For quark_se_ss, it was using a depth of 8. For EM Starterkit, it will be
32. Adding this now as a configurable option. A larger FIFO really helps
reduce SPI interrupts.
Change-Id: Id2bc8470bfc08ab447d38b89c7904cff010c63bd
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Just as rxftlr can be read, a macro is needed so that txftlr can be read.
Symmetry.
Change-Id: Id987f700d89268feca60850f4fdf512f990f3ab6
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
A recent submission caused a build error for DW
CONFIG_SPI_DW_INTERRUPT_SINGLE_LINE because the symbols
CONFIG_SPI_<0,1>_IRQ went missing from Kconfig.
I think these should probably NOT be configurable, because
on an SOC, interrupt lines are hard. So I'm changing
the names back to SPI_DW_PORT_<0,1>_IRQ, with there
definitions originatig in the soc.h file.
Also, on DesignWare ARC EM Starterkit, the SPI interface
has 6 slave selects, but IP itself can handle up to 16.
Why does this start from 1 and not 0? Argh!
DBG_COUNTER_RESULT() should expand to 0 when not used.
Also, don't check version from DesignWare IP because
it can be different for each target.
spi_dw_isr() requires a cast when converting arg to dev.
Change-Id: I83d55e0405583e7cafab80b09cbef44e0f96fcb8
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
* Rename BMP280 to BME280 which is a superset for the former.
* Autodetect device based on chip ID.
* Implement humidity fetching and reading for BME280
* Rename sample BMP280 to BME280
Change-Id: I565c769a7011e7496c9f1cad861d5ee311839b4f
Signed-off-by: Murtaza Alexandru <alexandru.murtaza@intel.com>
Check if return value is negative when checking for errors, instead of
checking if it's 0.
Change-Id: I0b0af28c02b3760f3128e8cbe48908dabc89af88
Signed-off-by: Murtaza Alexandru <alexandru.murtaza@intel.com>
Update all drivers that have vectorial data to return all 3 channels (X,
Y and Z) if the chan parameter is _ANY.
Also fix a compile bug in LSM9DS0 MFD driver.
Change-Id: I5bf261846bcd68c288b96997ff164726f75c151c
Signed-off-by: Murtaza Alexandru <alexandru.murtaza@intel.com>
This is actually a revert from a previous revert. This updates RPC
following the very recent firmware development.
This reverts commit a146f9ef28.
Change-Id: I67b517c3959b5b78a5ef80fbb338d6cc66e43e8e
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Remove the homegrown sensor delayed work API in favor of using the
system-wide workqueue. Drivers still have the option of using their own
fiber.
In a second step, drivers can be refactored to start and use their own
workqueue.
Change-Id: I70dea6fc2abcbc9e04ac1ed3c837483a3d3c4424
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Call bt_conn_security() the same way it is done in upstream code for
NBLE. Currently use BT_SECURITY_MEDIUM as default sec level.
Makes at least following cases pass:
...
1/6 GATT TC_GAR_CL_BI_05_C PASS
2/6 GATT TC_GAR_CL_BI_17_C PASS
3/6 GATT TC_GAR_CL_BI_22_C PASS
4/6 GATT TC_GAR_CL_BI_27_C PASS
5/6 GATT TC_GAR_CL_BI_33_C PASS
6/6 GATT TC_GAW_CL_BI_06_C PASS
...
Change-Id: I2a0c177a187db931e88e2f82a5bda1c0cc04a112
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add driver for the Grove Temperature Sensor which measures ambient
temperature.
Sensor reference page:
http://www.seeedstudio.com/wiki/Grove_-_Temperature_Sensor
Change-Id: I4f56224be5fa7a968749d5d4df8cb99a462c3c21
Origin: original
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Add driver for the Grove Light Sensor which detects changes in ambient light.
Sensor reference page:
http://www.seeedstudio.com/wiki/Grove_-_Light_Sensor
Origin: Original
Change-Id: I88ae20cc9faa8ab8f274b0bd7a114db5c1a87a91
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Use the same Kconfig infrastructure and options for all SPI drivers.
Jira: ZEP-294
Change-Id: I7097bf3d2e1040fcec166761a9342bff707de4dd
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Most of the values are SoC specific and come from the SoC definition,
not need to define them in Kconfig.
Jira: ZEP-294
Change-Id: I962ce36b7e2361ea77ae4178bb7c86c19a241c4e
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Most of the values are SoC specific and come from the SoC definition,
not need to define them in Kconfig.
Jira: ZEP-294
Change-Id: I7688ca523915e3fa8a1d28dea7a1d84a66b39d56
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This adds a notify_le_param_updated function to call registered
le_param_updated callbacks with new connection parameters.
Change-Id: Idd660f7ca024c2f7712a6a41a51db77e4fc82a00
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
This issues connection parametrs update on new connection event,
to mimic Zephyr stack behaviour.
Change-Id: Ic3fa86a02ff9a5135a026dfff6d2fbfb890656c1
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
This adds implementation of bt_conn_le_param_update function.
Connection parameters can be only issued while in slave role,
because, nRF51 supports this procedure over L2CAP only.
Closes ZEP-222.
Change-Id: I2bb5f718b60b8be279f333c9721629662c029a32
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
on_nble_gap_conn_update_evt gives information about new
connection parameters. These shall be stored in conn.
Closes ZEP-222.
Change-Id: I69e36136cfae98821b1f5467c72c94dbc6f1d10f
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
This function will be used by bt_conn_le_param_update to validate
parameters.
Change-Id: Icd60d74dae3bf467af4b7277d1516b978ba937a5
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
According to the data from nble_gap_connect_evt,
role_slave is "0 if connected as master, otherwise as slave",
so to be consistent with our API, this shall be mapped to
either BT_CONN_ROLE_MASTER or BT_CONN_ROLE_SLAVE.
Change-Id: Icf31ef02ea178e04cb28b2611e09b06c23f49704
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
Baohong Liu