Fixes the sht3xd sensor driver to store the user-supplied sensor
trigger as a pointer rather than a copy. This enables the trigger
handler to use CONTAINER_OF to retrieve a context pointer when the
trigger is embedded in a larger struct.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Fix the low readability read command which was swapped with high
readability. This should fix an issue which caused a sensor fetch
fail in low repeatability single shot mode (no data ready)
Signed-off-by: Wouter Cappelle <wouter.cappelle@crodeon.com>
Add CONFIG_CRC for building CRC related routines.
CRC routines are now being built for each application, whether used or
not and are add in the build system unconditionally.
Keep CONFIG_CRC enabled by default for now and until all users have
converted to use the new option.
Partial fix for #50654
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Refactors all sensor drivers to use SENSOR_DEVICE_DT_INST_DEFINE, which
is a sensor-specific variant of DEVICE_DT_INST_DEFINE that provides a
common place to instantiate additional data structures for the future
sensor subsystem and/or sensor driver stats.
This approach was inspired by I2C_DEVICE_DT_INST_DEFINE to streamline
adding I2C stats support across all I2C drivers.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
This change in pattern is meant to address a misconfiguration issue
that can occur for sensors that support being on multiple busses
like I2C & SPI.
For example, you can have a configuration in which such a sensor is
on the I2C bus in the devicetree and the sensor is enabled. However
the application configuration enables CONFIG_SPI=y and CONFIG_I2C=n
and this will cause the sensor driver to be built by default, however
since we don't have the I2C bus enabled the driver will not compile
correctly.
Previously we had been adding to board Kconfig.defconfig something
like:
config I2C
default y if SENSOR
This pattern doesn't scale well and may differ from what an application
specific need/use is.
So instead move to a pattern in which we leave the default enablement
up to the devicetree "status" property for the sensor. We then have
the Kconfig move from 'depends on <BUS>' to 'select <BUS>' and in
the case of drivers that support multiple busses we have the Kconfig
be: 'select <BUS> if $(dt_compat_on_bus,$(<DT_COMPAT>),<BUS>) for
each bus type the sensor supports.
This removes the need to add Kconfig logic to each board and enables
the bus subsystem and bus controller driver if the sensor requires
it by default in the build system.
Fixes: #48518
Signed-off-by: Kumar Gala <galak@kernel.org>
Update sensor drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
Signed-off-by: Kumar Gala <galak@kernel.org>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some drivers explicitely casted data/config from void * to the
corresponding type. However, this is unnecessary and, in many drivers it
has been misused to drop const qualifier (refer to previous commits).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
replace custom crc8 with sys/crc8
use sys_put/sys_get helpers for byteorder specific operations
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
In drivers/sensor/CMakeLists.txt, we have various lines like this:
add_subdirectory_ifdef(CONFIG_FOO foo)
Then drivers/sensor/foo/CMakeLists.txt says:
zephyr_library()
zephyr_library_sources_ifdef(CONFIG_FOO foo.c)
This is redundant; the foo/CMakeLists.txt won't be added to the build
system unless CONFIG_FOO=y in the first place, so there's no need for
extra boilerplate testing it again.
Remove all these unnecessary instances in each sensor driver's
CMakeLists.txt using this pattern:
zephyr_library()
zephyr_library_sources(foo.c)
In a couple of places, the '.c' extension is missing. Add them in for
consistency when that happens.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Currently there is no way to distinguish between a caller
explicitly asking for a semaphore with a limit that
happens to be `UINT_MAX` and a semaphore that just
has a limit "as large as possible".
Add `K_SEM_MAX_LIMIT`, currently defined to `UINT_MAX`, and akin
to `K_FOREVER` versus just passing some very large wait time.
In addition, the `k_sem_*` APIs were type-confused, where
the internal data structure was `uint32_t`, but the APIs took
and returned `unsigned int`. This changes the underlying data
structure to also use `unsigned int`, as changing the APIs
would be a (potentially) breaking change.
These changes are backwards-compatible, but it is strongly suggested
to take a quick scan for `k_sem_init` and `K_SEM_DEFINE` calls with
`UINT_MAX` (or `UINT32_MAX`) and replace them with `K_SEM_MAX_LIMIT`
where appropriate.
Signed-off-by: James Harris <james.harris@intel.com>
It is necessary to wrap the device pointer into data.
Which was done already on most of them when global trigger is enabled.
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
I think people might be reading differences into 'if' and 'depends on'
that aren't there, like maybe 'if' being needed to "hide" a symbol,
while 'depends on' just adds a dependency.
There are no differences between 'if' and 'depends on'. 'if' is just a
shorthand for 'depends on'. They work the same when it comes to creating
implicit menus too.
The way symbols get "hidden" is through their dependencies not being
satisfied ('if'/'depends on' get copied up as a dependency on the
prompt).
Since 'if' and 'depends on' are the same, an 'if' with just a single
symbol in it can be replaced with a 'depends on'. IMO, it's best to
avoid 'if' there as a style choice too, because it confuses people into
thinking there's deep Kconfig magic going on that requires 'if'.
Going for 'depends on' can also remove some nested 'if's, which
generates nicer symbol information and docs, because nested 'if's really
are so simple/dumb that they just add the dependencies from both 'if's
to all symbols within.
Replace a bunch of single-symbol 'if's with 'depends on' to despam the
Kconfig files a bit and make it clearer how things work. Also do some
other minor related dependency refactoring.
The replacement isn't complete. Will fix up the rest later. Splitting it
a bit to make it more manageable.
(Everything above is true for choices, menus, and comments as well.)
Detected by tweaking the Kconfiglib parsing code. It's impossible to
detect after parsing, because 'if' turns into 'depends on'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Update ALERT active level in all devicetree files. Capture GPIO flags
in static configuration. Add internal API to enable and disable
interrupt, to release the handlers when an alert occurs, and to
re-enable the signal when the handler completes. Check for alerts
received during periods when the interrupt was disabled.
Extend the example to handle both above and below range triggers and
alerts that are present on startup.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All sensors were using legacy log module registeration method
where LOG_LEVEL was defined before registeration. This method
was error prone as it requires preserving includes order.
Replaced with LOG_MODULE_REGISTER(foo, level).
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Re-run with updated script to convert integer literal delay arguments
to k_thread_create and K_THREAD_DEFINE to use the standard timeout
macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
For now there is only periodic data acquisition mode implemented.
This mode is quite power consuming. Based on datasheet in idle
state in periodic data acquisition mode SHT3X consumes 45uA but
in single shot mode 0.2uA. For many applications where power
consumption has to be kept as low as possible single shot mode
is the only choice. Tester on custom board NRF52832 + SHT31-DIS.
Signed-off-by: Michał Oleszczyk <oleszczyk.m@gmail.com>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sensor.h to drivers/sensor.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move i2c.h to drivers/i2c.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use the new i2c_write_read() wrapper to simplify the code.
Also add several overlays used to test the sensor on a variety of
boards, and conf file support for trigger testing.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add a configuration structure to sht3xd that holds instance-specific
parameters, implemented in a immutable statically allocated object
initialized with material from device tree binding aliases.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The sensor signal cannot be cleared by the application, so enabling
level triggers causes the system to hang as the callback is invoked
repeatedly. We want notification when the alarm state is entered, and
when it's exited, so use a double edge.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Nick Ward