Add bit definitions and set M/N divider ownership in
i2s_initialize.
Changes to comply with coding guidelines
Changes to address review comments
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Added support for fractional division of reference clock to obtain
I2S bit clocks
For example:
If reference clock is 38.4MHz and
if the I2S format is 2ch, 32bits per channel, 48KHz sample rate,
the bit clock frequency has to be 2*32*48K = 3.072MHz
38.4MHz/3.072MHz = 12.5 (a fraction)
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
The driver was using CONFIG_I2S_1_IRQ_PRI which doesn't exist. It
should use CONFIG_I2S_CAVS_1_IRQ_PRI.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the driver files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Until now, Zephyr has used a patched Kconfiglib that turns 'source' into
a globbing source (by replacing 'source' with 'gsource' at the token
level). There's two problems with this:
- The patch needs to be maintained separately
- Misspelled filenames are silently ignored, as they look like glob
patterns that don't match anything
Fix it as follows:
1. Replace all 'source' statements that use wildcards with 'gsource'
2. Remove the custom Kconfiglib patch so that 'source' no longer globs
The sed pattern '/source.*[*?]/s/source/gsource/' was run over all
Kconfig* files to do the replacement.
source's that use environment variables that might contain glob patterns
were manually changed to gsource.
Building the docs in doc/ is a good test, as doc/Makefile deliberately
sets the environment variables to glob up as many Kconfig files as
possible.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Implements the driver for Intel CAVS I2S. Only Playback
is currently supported.
Change-Id: I7b816f9736dc35e79a81d3664d6405dc0aac15b4
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Added Inter-IC Sound driver (based on SSC module) for Atmel
SAM MCU family.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-2509
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Sathish Kuttan