Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_PINS and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled gpio drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_GPIO_DEVICE and
HAS_DTS_GPIO.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_DEVICE and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These symbols were removed by commit 4e8f29f319 ("gpio: Refactor the
mcux gpio driver to use dts"). The settings should come from DTS now.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Adds dts bindings for the mcr20a wireless transceiver. The frdm_k64f
board supports the mcr20a via an Arduino shield, therefore the dts node
is added to the board dts. The kw2xd is a SiP and thus the mcr20a dts
node is added to the soc dts.
The networking samples using prj_frdm_k64f_mcr20a.conf have been broken
since the refactoring of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
And adding support for GPIO CS as well.
It looks like the driver could benefit from centralizing all SPI access
into a unique function, the protocol does not seem too convoluted to do
so, like CC2520 or CC1200.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
- Renaming NET_L2_RAW_CHANNEL to NET_RAW_MODE
- Create a generic IEEE 802.15.4 raw mode for drivers
- Modify the IEEE 802.15.4 drivers so it passes the packet unmodified,
up to code using that mode to apply the necessary changes on the
received net_pkt according to their needs
- Modify wpanusb/wpan_serial relevantly
Fixes#5004
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This patch allows the use of the MCR20A driver with KW2xD devices.
The clock output of the transceiver can be used as an input clock
for the PLL of the SoC. The hardware reset and CLK_OUT setup of
the transceiver should then be performed during the initialization
of the SoC. The driver is not allowed to do it again.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
fix misspelling in Kconfig files that would show up in configuration
documentation and screens.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Fix misspellings in Kconfig help text and made spelling of
RX and TX consistent (from reviewer comments)
Change-Id: Ie9d4c3863cd210e7a17b50a85a7e64156b6bf3d7
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This commit changes Kconfig prefix for ieee802154 drivers to
IEEE802154_*. This is done for consistency with config prefixes
used in other subsystems.
Change-Id: Ibbb4d96d2b748f4f13135bde85304ec34c5a90a6
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
This commit splits 802.15.4 drivers configuration into separate files.
Change-Id: Ie1bed862e8f4248240fef18bc211d0ee8ca1493c
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
Maureen Helm