Add native_posix USB virtual driver connected over USBIP to the Host
Linux.
Fixes: #9846
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Some of the events from USBD peripheral (i.e. cable disconnect)
were handled in IRQ context and some of them (i.e. ep r/w events) in
system workqueue (inherited from initial driver implementation).
This may lead to race condition in some specific situations.
Currently, all of the events are enqueued in ISR and processed in
workqueue. Driver is reinitialized on queue overflow and queue size
is configurable in KConfig.
Fixes#12016
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
Make the following nRF peripheral drivers:
- ADC
- GPIO
- I2C
- SPI
- UART
- USB_DEVICE
enabled by default so that users do not need to explicitly enable them
in their applications after choosing an nRF SoC as the build target.
Kconfig options enabling these drivers depend on both a given hardware
feature (e.g. I2C) and an nRF family SoC selected, so effectively they
will be automatically enabled only when it is adequate (and in most
cases these drivers are the only option for a given hardware feature
on nRF SoCs).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This patch adds a USB device driver for the USBHS device that can be
found on Atmel SAM E70 SoC family. Only the FIFO mode is supported
(as opposed to DMA). It supports LS, FS and HS modes, but defaults to
FS mode as Zephyr does not fully support HS mode yet.
Tested examples on an Atmel SMART SAM E70 Xplained Board:
* usb/cdc_acm
* usb/hid-mouse
* usb/mass
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
* Add usbd_dc_nrfx shim
The shim is based on the previous one usbd_dc_nrf5.
For handling the USBD hardware, tested nrfx_usbd driver from nRF SDK
was used.
Briefly tested examples:
* usb/cdc_acm
* usb/dfu (USB communication only due to flash handling issues)
* usb/hid-mouse
* bluetooth/hci_usb
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
Add support for usbotg_fs, by adding the DT fixup, pinmux macros,
and the DT entries in stm32f2.dtsi.
Signed-off-by: Istvan Bisz <istvan.bisz@t-online.hu>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The STM32F7 uses the same USB OTG FS controller than the STM32F4 series.
It is therefore trivial to add support for it, by adding the DT fixup
and pinmux macros, and the DT entries in stm32f7.dtsi. Keep it disabled,
it should be enabled at the board level.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Added CONFIG_USB_DW_USB_2_0
Updated global configuration register to use UTMI 16 bit PHY
Updated device configuration register to use High Speed
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Add usb disconnect pin support.
Some boards use a GPIO pin to controll a transistor,
which drives the pull-up resistor on USB DP pin.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
* Add USB device controller driver for nRF52840 SoC.
* Supports only Bulk and Interrupt endpoints for now.
* ISO endpoint support is WIP.
What's tested:
* BTUSB - LE Scanning and connection.
Known issues in btusb tests:
* Observed momentary delays during LE scanning. This is possibly
due to hci_usb's way of calling the usb_write().
* Sometimes, when LE scan stop command is issued, response is not
sent and as a result USB stops functioning. This is also related
to the way btusb is handling the write(). For some reason, the
btusb class handler seems to issue another data packet write before
the USB control transaction is complete.
Miscellaneous:
* Lots of TODO items to discuss and fix.
Origin: Original
Signed-off-by: Sundar Subramaniyan <sundar.subramaniyan@gmail.com>
Use "select USE_STM32_LL_USB/USE_STM32_HAL_PCD/USE_STM32_HAL_PCD_EX"
to select the needed STM32 HAL files, instead of editing
ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
This is a USB controller driver for STM32F4xx devices using
the STM32 Cube HAL_PCD framework. This has been tested with
the cdc_acm driver on a 96b_carbon board (STM32F401RE).
This is a refactoring of:
usb: usb_dc_stm: Add support for STM32Cube HAL_PCD USB driver
Signed-off-by: Christer Weinigel <christer@weinigel.se>
[daniel.thompson@linaro.org: Removed STM32F40(157) defconfig changes
together with STM32F4Discovery pinmux and defconfig changes, updated
clock settings and pad configuration to match latest mainline]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[giannis.damigos@gmail.com: Change uint*_t types to u*_t types,
change SYS_LOG_USB_DC_STM_LEVEL to SYS_LOG_USB_DRIVER_LEVEL and
update pinmux to match latest arm branch]
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
DesignWare USB driver is now using new system log macros, updated
the Kconfig variable to be a level rather than a bool and the .conf
files at samples.
JIRA: ZEP-311
Change-Id: Ief46cadd954ca4b30a3a1cf2eba6e44ccbc9bc9f
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Quark SE USB device (Designware IP) controller driver implements
the low level control routines to deal directly with the hardware.
Only FIFO mode supported.
Change-Id: I086186df017734579f0363ed79effc1481ff32c2
Signed-off-by: Adrian Bradianu <adrian.bradianu@windriver.com>
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Paweł Zadrożniak