Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references where
needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The board name for the nRF52 DK, so far known as nrf52_pca10040, is
renamed to nrf52dk_nrf52832. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to
match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Remove prompts from Kconfig options `UART_x_NRF_UART*` that select
the type of nrfx driver (for UART or UARTE peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding UART node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between UART and UARTE for a given instance.
Since all `UART_x_NRF_UART*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `I2C_x_NRF_TWI*` that select
the type of nrfx driver (for TWI or TWIM peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding I2C node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between TWI and TWIM for a given instance.
Since all `I2C_x_NRF_TWI*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add shield definition for the MikroElektronika ADC Click. The ADC
Click carries a MCP3204 12-bit Analog-to-Digital converter in a
mikroBUS form factor.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The LIS3MDL driver handles DRDY interrupt only. So connect
trigger to the DRDY pin instead of the INT pin.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
There is a blue LED used to display connectivity for the SparkFun
SARA-R4 shield. This LED is connected to the modem via GPIO 16
which is the default used by SARA-R4 driver when
CONFIG_MODEM_UBLOX_SARA_R4_NET_STATUS is enabled.
Signed-off-by: Michael Scott <mike@foundries.io>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update bluetooth hcp spi driver to new GPIO API.
Following changes have been done:
- Use new gpio api functions
- Get reset, irq and cs flags from dt defines
- Define reset pin as active low and invert set/unset logic.
Tested on disco_l475_iot1 and 96b_carbon.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Mark the INT signal to be active low and use the new functions to get
gpio state and configure the gpio interrupt flanks.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
This commit introduces the can-primary alias to identify
the primary CAN interface.
This alias is used for all samples and tests, so they don't
need to probe the right interface.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Remove link board can, shield was discontinued in
prototype status and will be replaced by a successor.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This shield adds analog and digital sensors to a TI LaunchPad
development kit. Currently only the ADXL362 accelerometer is supported.
This is useful for exercising the SPI interface. The analog sensors will
be useful if we add support for the sensor controller and ADC in the
future.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Add shield definition for the Texas Instruments LMP90100 Sensor Analog
Frontend (AFE) Evaluation Board (EVB).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move adafruit_2_8_tft_touch_v2 to Kconfig.defconfig format.
As part of this change Kconfig flags SPI and DISPLAY are removed
from the shield configuration as they are part of application
configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move dfrobot_can_bus_v2_0 to Kcondig.shield foramt and as part of
this change introduce nrf52_pca10040 board specific configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move link_board_can to conditional Kconfig.
As part of this change, some board specific symbols are moved
to reel_board specific file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move sparkfun_sara_r4 to conditional Kconfig.
As part of this change, remove disco_l475_iot1 specific configuration
as it is already part of board default configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Factorize definitions for ssd1306_128x32 and sd1306_128x64 shields
and move to conditional Kconfig.
As part of this change, direct drivers Kconfig symbols enabling
(I2C, SSD1306) are removed as they are application responsibility.
Also disabling SSD16XX is removed as SSD16XX should not be enabled
by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move wavehare epaper shields to conditional Kconfig.
As part of this change, direct drivers Kconfig symbols enabling
(SPI, SSD16XX) are removed as they are application
responsibility. GPIO is removed as well as it should be 'y' by
default on all boards according to Default board configuration
guidelines.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Put shield configuration Kconfig flags in new Kconfig.defconfig.
This way shield BLE subsystem can now be selected by application
using NETWORKING symbol, similarly to what is done when modem is
directly present on board.
Additionally, move board Kconfig files to a similar scheme where
shields related Kconfig flags are made available under shield,
board and NETWORKING symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Put shield configuration Kconfig flags in new Kconfig.defconfig.
This way shield BLE susbystem can now be selected by application
using BT symbol, similarly to what is done when BlueNRG ship is
directly present on board.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Marc Reilly