move adc.h to drivers/adc.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
We should not be storing the sequence pointer, as
adc_read_async() returns immediately. The memory could
be heap allocated, or on a call stack. Make a copy of
it instead.
Fixes: #15039
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Commit aad21ecb31 introduced an incorrect
pattern of handling ADC sampling requests with invalid parameters in
both nRF ADC drivers. After discarding such request, the drivers do not
release properly the access lock and therefore become unusable.
Unfortunately, this pattern were later on copied in all other ADC
drivers in the source tree.
This commit adds the proper lock releasing in all the affected drivers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Improve initialization of the ADC.
After initialization with the default values, the clock source
of the ADC is asynchronous clock (ADACK) and clock divide ratio
is 8. The minimum conversion clock frequency is 1MHz.
Add clock divider selection and set default divide ratio to 1.
That sets the conversion clock frequency to approximately 5MHz.
Default configuration for the voltage reference is set to
external pins V_REFH and V_REFL. Depending on the MCU configuration
V_REFL may be connected to ground and V_REFH to VREF_OUT.
Since Voltage Reference block is not supported, the ADC does not work
properly on FRDM-KW41Z. Add voltage reference selection to fix it.
Enable self-calibration function as recommeded in Reference Manual.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Major rework of the mcux adc16 driver to convert it to the new adc api.
Currently supports a subset of the api features including synchronous
and asynchronous reads, and consecutive reads triggered by the kernel
timer.
Does not yet support some of the channel configuration options such as
gain and reference voltage because the hardware only allows these
options to be configured by peripheral instance rather than by channel.
The values are currently hardcoded in the driver, but in the future we
could introduce some flexibility per instance via device tree
attributes.
Does not yet support consecutive reads triggered by a hardware timer.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux adc16 driver to adapt it to the Zephyr
adc interface.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Anas Nashif