This driver doesn't provide any API, it only initializes the pinmux
controller to appropriate values depending on the board.
The first board to use this new infrastructure is the Arduino 101 board,
because it is alphabetically the first.
To better organize code for the different SoCs and boards, a "family"
level is created in the 'drivers/pinmux' directory. The Arduino 101
board is part of the Quark MCU "family".
The PINMUX_DEV configuration (and functionality) is removed for now, it
will be added back when the pinmux_dev drivers are (re)introduced, with
clearer semantics.
Change-Id: Idf5cc3caf6be620aa50828ae8fdc535df6caf458
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Add a common driver for pin control subsystem in STM32 MCU series. The
driver allows for selection of pin's function without the ability of pin
remapping.
The driver implements a pinmux driver API, with custom `func` and `pin`
encoding in API calls. The caller is expected to use STM32PIN() helper
macro for encoding port/pin numbers or using one of the provided
STM32_PIN_* defines.
The common driver requires SoC specific support to be implemented. The
SoC code must implement these calls: stm32_get_pin_config(),
stm32_get_port_clock(), stm32_pin_configure(). Consult pinmux_stm32.h
header for detailn on semantics of these calls.
The driver also requires board level integration. The call
stm32_board_get_pinconf() is expected to privide pin function
assignments for the target board.
Whenever an IO pin is being enabled, the driver will automatically
enable the clock for corresponding port. The driver does not implement
disabling of port's clock as this has potentially disruptive, as such
such operation should be done explicitly in the code.
The pin control module needs to be initialized before any other modules,
but after clock_control. For this reason, the driver is initialized by
default at PRIMARY level, with priority set to 2. The priority can be
changed through configuration.
Change-Id: I8cb746d0f3cad72cd50b3355fe6d93a9f469be25
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
K64 pinmux support is created as a normal driver.
As opposed to the Galileo board, the pin configuration options are
defined by the MCU and are not board-specific. Separate
platform/board-specific configuration code uses the pinmux driver for
the default pin settings. For FRDM-K64F, only the Arduino pins (22 of a
possible 160) are set up.
Some of the I/O pins routed to the Arduino header are also configured as
JTAG/SWD signals by default and are used by the OpenSDAv2 debug
interface. Therefore, a PRESERVE_JTAG_IO_PINS config option was created
for the FRDM-K64 platform to prevent the default pin settings from
re-configuring these pins.
The K64 MCU separates pin configuration and control, implemented in the
pinmux driver, from GPIO. This results in some cross referencing
between the K64 GPIO driver and the K64 pinmux driver due to the
dependencies of one on the other.
This pinmux driver also uses the expanded pinmux function/mode parameter
size to describe pin configuration options with bit fields for the K64,
including up to 8 pin functions, plus interrupt, pullup/down, drive
strength, open-drain and slew rate.
The following GCC warnings in the K64 pinmux driver are prevented when not
compiling with 'no-optimization' (-O0):
warning: 'gpio_dev' may be used uninitialized in this function
[-Wmaybe-uninitialized]
Change-Id: Ie5031d18750143bf895883058b3cd55fd9989fd3
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
Vinicius Costa Gomes