Remove soc/arm/st_stm32/stm32YY/flash_registers.h files.
Change register accesses in stm32 flash drivers to use FLASH_TypeDef
from modules/hal/stm32/stm32cube/stm32YYxx/soc/stm32xxxxxx.h.
Fixes#16235
Signed-off-by: Sarvesh Patkar <psarvesh314@gmail.com>
move flash.h to drivers/flash.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
On STM32F3 devices, a trick was required for normal use of registers.
This was actually an issue in flash registers defintions which should
be defined as volatile.
Fix this and additionaly, fix definition for STM32F1 which was also
lacking the volatile instruction.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
A common driver is shared between stm32 chips, which was not the case
for stm32f3 series. As a consequence stm32f3 was not maintained
equally and was missing features such as flash layout or dts based
configuration.
Besides, drivers had some flows such as wrong bus clock and
missing HSI clock activation which lead to issues on boards not
using HSI as main clock.
As a consequence this commit moves stm32f3 series flash driver to
common stm32 flash drivers.
Fixes#4197
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Write-block-size values were filled for nRF5, STM32, QMSI, MCUX and
w25qxxdv devices.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08f51e2bfd475f6245771c1bd2df7ffc744c48c4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
After activation of cube based driver support on L4 and F3 series,
this commits performs the clean up of F3 and L4 relative code to
native clock control drivers.
Indirectly, it makes pwm driver supported de facto on F3 series
Change-Id: Idac17103a9b5ef6eab540719343cc8f5865f15fa
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update stm32f3xx flash driver to support it.
Clean up will be done afterwards.
Change-Id: I3260bb063f714fa29adbc71d8036f20479a99b34
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Sarvesh Patkar