Add conditions to enable ptp_clock driver implementation
for native_posix when PTP subsystem is enabled.
Signed-off-by: Adam Wojasinski <awojasinski@baylibre.com>
As the automatic start requires that the zephyr exe is run as
a root user, it is somewhat cumbersome to use. Remove the script
support and require that the zeth device is created beforehand
by the net-setup.sh script found in net-tools zephyr project.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add Kconfig to set sleep timeout between empty read attempts in rx thread
for ethernet native posix driver.
Signed-off-by: Nicola Ochsenbein <Nicola.Ochsenbein@husqvarnagroup.com>
Quite a few of the drivers meant for the POSIX arch
interacted with the host directly, and will not
work when we use an embedded libC.
Until we fix them, let's add the appropriate
kconfig dependencies to avoid users trying to build them.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add gPTP multiport support to native_posix Ethernet driver.
This means that the driver is able to create more than one
network interface and enable gPTP to each of them. This requires
that net-tools is updated as it contains configuration file
for network interfaces in host side.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This is mainly testing purpose from native_posize ethernet
driver. Enable CONFIG_ETH_NATIVE_POSIX_VLAN_TAG_STRIP to have
VLAN tag strip feature on ethernet Rx frames.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If gPTP is enabled, then enable also PTP clock driver so that
gPTP sync starts to work properly for native_posix board.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Change the default behaviour of the host network interface
setup. Now user needs to execute net-setup.sh script from
net-tools project to setup host ethernet interface. The script
needs to be run as a root user. Then zephyr.exe can be started
as a normal user.
Example:
cd net-tools
sudo ./net-setup.sh
This will create zeth network interface and set IP address and
routes properly. See other command line options by typing
./net-setup.sh --help
Old behaviour is still there if one enables
CONFIG_ETH_NATIVE_POSIX_STARTUP_AUTOMATIC=y
in which case one needs to use the command
sudo --preserve-env zephyr.exe
to start the Zephyr process.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Allow user to configure a program that is executed after the
network interface is created and IP address is setup.
This can be used e.g., to start wireshark to capture
the network traffic of the interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
- Remove redundant 'n' defaults. 'n' is the default value for bool
symbols.
This makes the auto-generated documentation clearer as well: You get
"implicitly defaults to n" instead of
"- n if <propagated dependencies>".
- Shorten
<type>
prompt "foo"
to
<type> "foo"
This works for all types, not just bool.
- Various formatting nits.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Allow gPTP code to be run as a linux process and communicate
with gPTP daemon running in linux host.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
As the native_posix board has ethernet driver, then enable it by
default if networking is enabled in prj.conf file. This way we can
use generic networking config file when running the application
for native_posix board.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This creates zeth network interface in your host and allows user
to send and receive data sent to this network interface.
Fixes#6007
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Adam Wojasinski