In the case that there is a situation where the controller
oscillator start-up timer doesn't expire, or the SPI can't
read the CLKRDY bit the driver would hang during init.
The config option ETH_ENC28J60_CLKRDY_INIT_WAIT_MS sets
the time that the driver will wait for OST before returning
an ETIMEDOUT error.
Signed-off-by: Dean Sellers <dsellers@evos.com.au>
Allow defining multiple instances of enc28j60.
Remove the ETH_ENC28J60_0 Kconfig option along with this.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Add the `full-duplex` property for the `microchip,enc28j60` node.
Replace ETH_ENC28J60_0_FULL_DUPLEX Kconfig option with this property.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
* Utilize DT_HAS_<COMPAT>_ENABLED for devicetree based drivers
* Move to using 'select SPI' instead of 'depends on'
(see commit df81fef944 for
more details)
Signed-off-by: Kumar Gala <galak@kernel.org>
Use DT_INST_SPI_DEV_HAS_CS_GPIOS() in drivers to determine if we should
utilize CS_GPIO base SPI chipselect handling. This allows us to remove
Kconfig option for this feature.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Driver for networking device Microchip ENC28J60 is used as SPI slave,
moved to DTS type definition. Samples echo_client and echo_server use
this device on Arduino 101 board.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Let's use the new SPI API and ditch the old one.
Signed-off-by: Matthias Boesl <matthias.boesl@gmail.com>
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The enc28j60's reception routine requires a timeout
for a buffer assignation. The timeout is configurable
to allow a per application fine tuning.
The effect that K_NO_WAIT currently has is that there are frames
lost everytime that a buffer is required and there are none
available.
Jira: ZEP-1169
Change-Id: Ia18736fd85daee51fe1c2304977209cc7f0038b5
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
All sample applicatons in Zephyr, using the ENC28J60 driver, set
the ETH_ENC28J60_0_GPIO_PIN Kconfig variable to 19.
However, in the Kconfig.enc28j60 file this variable is set to 24.
That default value, 24, was used only during the first iterations
of this driver and never used again.
In this patch, we set the Kconfig variable to 19 and simplify
project configuration files by removing one line.
Change-Id: I3d5fd9da04a3f10845d2a409de56f5b9c235e995
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Such stack size might vary if debug is enabled or not and depending also
on other factors. Let's do the same for priority as well, putting it to
high prio as default (15 is way too low level).
Change-Id: I16afab33895085bacdef087fe70adeb1ae3ca2ab
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The default kernel init priority is too low. Make this
configurable and set the default priority so that the
ethernet driver is started just before the network stack.
This commit adds generic ethernet priority and changes
currently available ethernet drivers to use it.
Change-Id: If695e52b6dd9ea227f10ba306bb145d72d2312b0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The driver originally gets the full-duplex configuration
from the PHCON1 register and PDPXMD bit as stated by the
ENC298J60 specification document section 2.6 "LED Configuration".
This section trust the board to LEDB connection to signal the
full-duplex configuration.
This commit gets the full-duplex configuration from Kconfig
symbols to allow a proper functionality even when the board
is not connecting LEDB apropriately.
Change-Id: I803958409a611e23e2c3e03f40b412f1695947af
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
Adds the ENC28J60 Ethernet module driver.
Origin: Original
JIRA: ZEP-291
Change-Id: I2b5790ecb251f9059f172bcaafadef24bd27207a
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
Dean Sellers