Add MAX78002EVKIT board.
For more information about this board please check
https://www.analog.com/
Signed-off-by: Furkan Akkiz <hasanfurkan.akkiz@analog.com>
This updates the documentation of all the Analog Devices boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Configures pins for the SPI instance attached to the Arduino connector
to enable using this board with the eval_adxl372_ardz shield.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Configures pins for the GPIOs attached to the Arduino connector to
enable using this board with the eval_adxl372_ardz shield.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Full name was set based on the information available either in board
documentation or in Twister files.
Whenever applicable, vendor name was dropped from the full name so that
all boards have a consistent naming scheme.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Front picture was listed twice, despite the back picture
(max32666fthr_img2.jpg) actually being checked into the repo, so switch
to that one.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
MAX32662EVKIT board has CFAF128128B1-0145T display which
is 128x128 graphic display.
This commit enable mpi dbi display support with LVGL graphic library.
Pin connection of display is 3wire mode
SRAM size increased to be fit with lvgl example.
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Adds missing code-sample directive to the Hello World sample in
preparation for upcoming changes to the Zephyr documentation that will
be leveraging the provided description and metadata.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
`CLOCK_CONTROL` subsystem being selected directly at family level,
remove it from individual board configurations.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Adds a new board definition for the ADI MAX32690FTHR board. This board
uses the same SoC as the MAX32690EVKIT board, but with a smaller feather
form factor.
Tested on hardware with the following samples:
- samples/hello_world
- samples/basic/blinky
- samples/basic/threads
- samples/subsys/shell/shell_module
- samples/subsys/input/input_dump
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Configures pins for the SPI instance attached to the Pmod connector to
enable using this board with the pmod_acl shield.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
MAX32690EVKIT board has CFAF128128B1-0145T display which
is 128x128 graphic display.
The pins goes to display is not standard SPI interface, it requires
SPI bitbanging to drive display.
This commit enables mpi dbi display support with LVGL graphic library
Pin connection of display is 3wire mode
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
MAX32680EVKIT board has CFAF128128B1-0145T display which
is 128x128 graphic display.
This commit enables mpi dbi display support with LVGL graphic library
Pin connection of display is 3wire mode
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
MAX32672EVKIT board has CFAF128128B1-0145T display which
is 128x128 graphic display.
This commit enable mpi dbi display support with LVGL graphic library.
Pin connection of display is 3wire mode
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Furkan Akkiz