OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/boards/arm/twr_ke18f/Kconfig

30 lines
693 B
Plaintext
Raw Normal View History

kconfig: Clean up header comments and make them consistent Use this short header style in all Kconfig files: # <description> # <copyright> # <license> ... Also change all <description>s from # Kconfig[.extension] - Foo-related options to just # Foo-related options It's clear enough that it's about Kconfig. The <description> cleanup was done with this command, along with some manual cleanup (big letter at the start, etc.) git ls-files '*Kconfig*' | \ xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /' Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-11-01 20:45:29 +08:00
# TWR-KE18F board configuration
boards: twr-ke18f: add support for the NXP TWR-KE18F board Add support for the NXP TWR-KE18F development board. This board feautures an NXP MKE18F16 MCU, a selection of user LEDs and push-buttons, potentiometer, thermistor, CAN interface, and FlexIO header. Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
2019-05-08 02:24:03 +08:00
# Copyright (c) 2019 Vestas Wind Systems A/S
# SPDX-License-Identifier: Apache-2.0
if BOARD_TWR_KE18F
config BOARD_TWR_KE18F_FLEXIO_CLKOUT
bool "Enable CLKOUT signal on FlexIO header"
depends on PINMUX_MCUX_PORTE
help
Enable the CLKOUT signal on FlexIO header pin 7 (PTE10).
boards: arm: twr_ke18f: add SPI support Add SPI support to the NXP TWR-KE18F development board. There are no onboard SPI devices, but both SPI busses are available on the primary Tower System elevator connector. Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
2019-05-16 17:51:26 +08:00
config BOARD_TWR_KE18F_SPI_0_PCS2
bool "Use PTE6 as dedicated SPI_0 PCS2 chip select"
depends on SPI_0
default y
config BOARD_TWR_KE18F_SPI_1_PCS0
bool "Use PTD3 as dedicated SPI_1 PCS0 chip select"
depends on SPI_1
default y
config BOARD_TWR_KE18F_SPI_1_PCS2
bool "Use PTA16 as dedicated SPI_1 PCS2 chip select"
depends on SPI_1
default y
kconfig: Global whitespace/consistency cleanup Clean up space errors and use a consistent style throughout the Kconfig files. This makes reading the Kconfig files more distraction-free, helps with grepping, and encourages the same style getting copied around everywhere (meaning another pass hopefully won't be needed). Go for the most common style: - Indent properties with a single tab, including for choices. Properties on choices work exactly the same syntactically as properties on symbols, so not sure how the no-indentation thing happened. - Indent help texts with a tab followed by two spaces - Put a space between 'config' and the symbol name, not a tab. This also helps when grepping for definitions. - Do '# A comment' instead of '#A comment' I tweaked Kconfiglib a bit to find most of the stuff. Some help texts were reflowed to 79 columns with 'gq' in Vim as well, though not all, because I was afraid I'd accidentally mess up formatting. Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-11-01 17:24:07 +08:00
endif # BOARD_TWR_KE18F