OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/drivers/sensor/bmm150/Kconfig

52 lines
1.1 KiB
Plaintext
Raw Normal View History

kconfig: Clean up header comments and make them consistent Use this short header style in all Kconfig files: # <description> # <copyright> # <license> ... Also change all <description>s from # Kconfig[.extension] - Foo-related options to just # Foo-related options It's clear enough that it's about Kconfig. The <description> cleanup was done with this command, along with some manual cleanup (big letter at the start, etc.) git ls-files '*Kconfig*' | \ xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /' Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-11-01 20:45:29 +08:00
# BMM150 Geomagnetic sensor configuration options
driver: sensor: Add BMM150 Geomagnetic sensor driver This patch implements BMM150 driver with polling mode and its tested with original BMM150 sensor hardware. Driver works on I2C interface as of now. Following datasheet is taken as reference while developing driver. http://www.mouser.com/ds/2/783/BST-BMM150-DS001-01-786480.pdf Signed-off-by: Punit Vara <punit.vara@intel.com>
2017-05-31 13:04:40 +08:00
# Copyright (c) 2017 Intel Corporation
# SPDX-License-Identifier: Apache-2.0
menuconfig BMM150
bool "BMM150 I2C Geomagnetic Chip"
drivers: sensor: Update drivers to use devicetree Kconfig symbol Update sensor drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol to expose the driver and enable it by default based on devicetree. Signed-off-by: Kumar Gala <galak@kernel.org>
2022-07-20 11:41:45 +08:00
default y
depends on DT_HAS_BOSCH_BMM150_ENABLED
drivers: sensor: clean up Kconfig files - place all sensor Kconfig options in submenu - separate device drivers and common options with a comment line - align help text Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
2017-09-22 02:28:16 +08:00
depends on I2C
driver: sensor: Add BMM150 Geomagnetic sensor driver This patch implements BMM150 driver with polling mode and its tested with original BMM150 sensor hardware. Driver works on I2C interface as of now. Following datasheet is taken as reference while developing driver. http://www.mouser.com/ds/2/783/BST-BMM150-DS001-01-786480.pdf Signed-off-by: Punit Vara <punit.vara@intel.com>
2017-05-31 13:04:40 +08:00
help
Enable driver for BMM150 I2C-based Geomagnetic sensor.
if BMM150
choice
prompt "Default preset"
default BMM150_PRESET_REGULAR
help
Specify the default preset (x/y oversampling, z oversampling, sampling
frequency).
config BMM150_PRESET_LOW_POWER
bool "Low power (3, 3, 10)"
config BMM150_PRESET_REGULAR
bool "Regular (9, 15, 10)"
config BMM150_PRESET_ENHANCED_REGULAR
bool "Enhanced regular (15, 27, 10)"
config BMM150_PRESET_HIGH_ACCURACY
bool "High accuracy (47, 83, 20)"
endchoice
config BMM150_SAMPLING_RATE_RUNTIME
kconfig: remove Enable from boolean prompts According to Kconfig guidelines, boolean prompts must not start with "Enable...". The following command has been used to automate the changes in this patch: sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig* Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
2022-03-09 19:05:12 +08:00
bool "Dynamic sampling rate"
driver: sensor: Add BMM150 Geomagnetic sensor driver This patch implements BMM150 driver with polling mode and its tested with original BMM150 sensor hardware. Driver works on I2C interface as of now. Following datasheet is taken as reference while developing driver. http://www.mouser.com/ds/2/783/BST-BMM150-DS001-01-786480.pdf Signed-off-by: Punit Vara <punit.vara@intel.com>
2017-05-31 13:04:40 +08:00
help
Enable alteration of sampling rate attribute at runtime.
config BMM150_SAMPLING_REP_XY
kconfig: remove Enable from boolean prompts According to Kconfig guidelines, boolean prompts must not start with "Enable...". The following command has been used to automate the changes in this patch: sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig* Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
2022-03-09 19:05:12 +08:00
bool "Dynamic XY oversampling"
driver: sensor: Add BMM150 Geomagnetic sensor driver This patch implements BMM150 driver with polling mode and its tested with original BMM150 sensor hardware. Driver works on I2C interface as of now. Following datasheet is taken as reference while developing driver. http://www.mouser.com/ds/2/783/BST-BMM150-DS001-01-786480.pdf Signed-off-by: Punit Vara <punit.vara@intel.com>
2017-05-31 13:04:40 +08:00
help
Enable alteration of XY oversampling at runtime.
config BMM150_SAMPLING_REP_Z
kconfig: remove Enable from boolean prompts According to Kconfig guidelines, boolean prompts must not start with "Enable...". The following command has been used to automate the changes in this patch: sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig* Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
2022-03-09 19:05:12 +08:00
bool "Dynamic Z oversampling"
driver: sensor: Add BMM150 Geomagnetic sensor driver This patch implements BMM150 driver with polling mode and its tested with original BMM150 sensor hardware. Driver works on I2C interface as of now. Following datasheet is taken as reference while developing driver. http://www.mouser.com/ds/2/783/BST-BMM150-DS001-01-786480.pdf Signed-off-by: Punit Vara <punit.vara@intel.com>
2017-05-31 13:04:40 +08:00
help
Enable alteration of Z oversampling at runtime.
endif # BMM150