OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/drivers/modem/Kconfig.wncm14a2a

49 lines
1.4 KiB
Plaintext
Raw Normal View History

kconfig: Clean up header comments and make them consistent Use this short header style in all Kconfig files: # <description> # <copyright> # <license> ... Also change all <description>s from # Kconfig[.extension] - Foo-related options to just # Foo-related options It's clear enough that it's about Kconfig. The <description> cleanup was done with this command, along with some manual cleanup (big letter at the start, etc.) git ls-files '*Kconfig*' | \ xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /' Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-11-01 20:45:29 +08:00
# WNCM 14A2A driver options
drivers: modem: wistron kconfig separation Separates Kconfig to a separate file. Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
2019-02-14 17:21:27 +08:00
# Copyright (c) 2018 Foundries.io
# SPDX-License-Identifier: Apache-2.0
menuconfig MODEM_WNCM14A2A
kconfig: remove Enable from boolean prompts According to Kconfig guidelines, boolean prompts must not start with "Enable...". The following command has been used to automate the changes in this patch: sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig* Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
2022-03-09 19:05:12 +08:00
bool "Wistron LTE-M modem driver"
drivers: modem: wistron kconfig separation Separates Kconfig to a separate file. Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
2019-02-14 17:21:27 +08:00
select MODEM_RECEIVER
select NET_OFFLOAD
drivers: modem: wnc-m14a2a: imply GPIO usage CONFIG_GPIO may not be enabled on some HW, so let's make sure to enable it if the dependencies are met, as the WNC-M14A2A driver needs to set power, reset and other GPIOs. Signed-off-by: Michael Scott <mike@foundries.io>
2019-03-08 02:00:00 +08:00
imply GPIO
drivers: modem: wistron kconfig separation Separates Kconfig to a separate file. Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
2019-02-14 17:21:27 +08:00
help
Choose this setting to enable Wistron WNC-M14A2A LTE-M modem driver.
NOTE: Currently the pin settings only work with FRDM K64F shield.
if MODEM_WNCM14A2A
config MODEM_WNCM14A2A_RX_STACK_SIZE
int "Size of the stack for the WNC-M14A2A modem driver RX thread"
default 1028
help
This stack is used by the WNCM14A2A RX thread.
config MODEM_WNCM14A2A_RX_WORKQ_STACK_SIZE
int "Size of the stack for the WNC-M14A2A modem driver work queue"
default 2048
help
This stack is used by the work queue to pass off net_pkt data
to the rest of the network stack, letting the rx thread continue
processing data.
config MODEM_WNCM14A2A_APN_NAME
string "APN name for establishing network connection"
default "m2m.com.attz"
help
This setting is used in the AT%PDNSET command to set the APN name
for the network connection context. Normally, don't need to change
this value.
config MODEM_WNCM14A2A_INIT_PRIORITY
int "WNC-M14A2A driver init priority"
default 80
help
WNC-M14A2A device driver initialization priority.
Do not mess with it unless you know what you are doing.
Note that the priority needs to be lower than the net stack
so that it can start before the networking sub-system.
kconfig: drivers: modem: Remove redundant MODEM_WNCM14A2A deps These symbols are already within an 'if MODEM_WNCM14A2A', so no need to put 'depends on MODEM_WNCM14A2A' on them. Also remove a redundant 'depends on MODEM' from MODEM_WNCM14A2A. drivers/modem/Kconfig.wncm14a2a is already sourced within an 'if MODEM', in drivers/modem/Kconfig. 'if FOO' is just shorthand for adding 'depends on FOO' to each item within the 'if'. Dependencies on menus work similarly. There are no "conditional includes" in Kconfig, so 'if FOO' has no special meaning around a source. Conditional includes wouldn't be possible, because an if condition could include (directly or indirectly) forward references to symbols not defined yet. Tip: When adding a symbol, check its dependencies in the menuconfig ('ninja menuconfig', then / to jump to the symbol). The menuconfig also shows how the file with the symbol got included, so if you see duplicated dependencies, it's easy to hunt down where they come from. Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-03-07 12:20:40 +08:00
endif # MODEM_WNCM14A2A