zephyr/drivers/serial/Kconfig.gecko

# Gecko SDK UART

# Copyright (c) 2017, Christian Taedcke
# SPDX-License-Identifier: Apache-2.0

config UART_GECKO
	bool "Gecko UART/USART driver"
	depends on HAS_SILABS_GECKO
	depends on GPIO_GECKO
	select SERIAL_HAS_DRIVER
	select SERIAL_SUPPORT_INTERRUPT
	select SOC_GECKO_USART
	help
	  Enable the Gecko uart driver.
kconfig: Clean up header comments and make them consistent Use this short header style in all Kconfig files: # <description> # <copyright> # <license> ... Also change all <description>s from # Kconfig[.extension] - Foo-related options to just # Foo-related options It's clear enough that it's about Kconfig. The <description> cleanup was done with this command, along with some manual cleanup (big letter at the start, etc.) git ls-files 'Kconfig' \| \ xargs sed -i -E '1 s/#\sKconfig[\w.-]\s-\s/# /' Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> 2019-11-01 20:45:29 +08:00			`# Gecko SDK UART`

drivers: serial: Add uart driver for Silabs EXX32 MCUs Signed-off-by: Christian Taedcke <hacking@taedcke.com> 2017-04-06 01:06:17 +08:00			`# Copyright (c) 2017, Christian Taedcke`
			`# SPDX-License-Identifier: Apache-2.0`

kconfig: Turn pointless/confusing 'menuconfig's into 'config's Defining a symbol with 'menuconfig' just tells the menuconfig to display any dependent symbols that immediately follow it in a separate menu. 'menuconfig' has no effect on symbol values. Making a symbol that doesn't have any dependent symbols after it a 'menuconfig' should be avoided, because then you end up with an empty menu, which is shown as e.g. [] Enable foo --- This is how it would be shown if there were children but they all happened to be invisible as well. With a regular 'config', it turns into [] Enable foo Change all pointless 'menuconfig's to 'config's. See the section on 'menuconfig' on the Kconfig - Tips and Best Practices page as well. Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> 2019-10-22 07:04:04 +08:00			`config UART_GECKO`
drivers: Add more uart instances for Silabs Devices Add more uart/usart instances for Silabs Gecko Devices and remove the *_GPIO_LOC configs. Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com> 2018-07-19 12:19:32 +08:00			`bool "Gecko UART/USART driver"`
drivers: serial: Add uart driver for Silabs EXX32 MCUs Signed-off-by: Christian Taedcke <hacking@taedcke.com> 2017-04-06 01:06:17 +08:00			`depends on HAS_SILABS_GECKO`
			`depends on GPIO_GECKO`
			`select SERIAL_HAS_DRIVER`
			`select SERIAL_SUPPORT_INTERRUPT`
soc: silabs_exx32: Add independent Kconfig options for HAL libraries Zephyr gecko drivers depend on libraries provided by the vendor. The same libraries may also be used directly by the application code or RAIL library. To facilitate the latter use case scenario this commit adds Kconfig options to independently enable compilation of vendor HAL library modules. Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com> 2018-12-12 23:30:00 +08:00			`select SOC_GECKO_USART`
drivers: serial: Add uart driver for Silabs EXX32 MCUs Signed-off-by: Christian Taedcke <hacking@taedcke.com> 2017-04-06 01:06:17 +08:00			`help`
			`Enable the Gecko uart driver.`