OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/samples/net/lwm2m_client/frdm_k64f.overlay

22 lines
443 B
Plaintext
Raw Normal View History

boards: frdm_k64f: move modem configurtion to overlay The wncm14a2a modem is an add-on/shield and not part of the frdm_k64f board and should be maintained and configured outside of the board. This needs to be moved to a shield, see #10965. Signed-off-by: Anas Nashif <anas.nashif@intel.com>
2018-10-31 19:30:23 +08:00
/*
* Copyright (c) 2018 Intel Corporation
*
* SPDX-License-Identifier: Apache-2.0
*/
&uart2 {
samples: net: lwm2m_client: add "ok" and baud rate to k64f overlay During the modem overlay move from the K64F board directory to the LwM2M sample code, 2 DTS entries were dropped: current-speed = <115200>; status = "ok"; Without these entries the DTS defines for UART2 and CURRENT_SPEED are missing from the generated_dts_board.h file. Signed-off-by: Michael Scott <mike@foundries.io>
2018-11-17 05:22:44 +08:00
current-speed = <115200>;
samples: lwm2m_client: enable HW flow control for WNC-M14A2A modem The WNC-M14A2A modem is supposed to use HW flow control on the UART connected to the MCU. In the past, we were able to bypass this requirement by using only the LTE-M firmware which supported pulling the CTS line high via "send-ok" gpio. This does NOT work for the LTE firmware. Now that MCUX UART driver supports hw-flow-control setting, let's use it in the modem overlay so that regardless of modem firmware (LTE vs. LTE-M) the sample will "just work". Signed-off-by: Michael Scott <mike@foundries.io>
2019-01-30 03:47:32 +08:00
hw-flow-control;
samples: net: lwm2m_client: add "ok" and baud rate to k64f overlay During the modem overlay move from the K64F board directory to the LwM2M sample code, 2 DTS entries were dropped: current-speed = <115200>; status = "ok"; Without these entries the DTS defines for UART2 and CURRENT_SPEED are missing from the generated_dts_board.h file. Signed-off-by: Michael Scott <mike@foundries.io>
2018-11-17 05:22:44 +08:00
status = "ok";
boards: frdm_k64f: move modem configurtion to overlay The wncm14a2a modem is an add-on/shield and not part of the frdm_k64f board and should be maintained and configured outside of the board. This needs to be moved to a shield, see #10965. Signed-off-by: Anas Nashif <anas.nashif@intel.com>
2018-10-31 19:30:23 +08:00
wncm14a2a {
compatible = "wnc,m14a2a";
label = "wncm14a2a";
mdm-boot-mode-sel-gpios = <&gpioc 17 0>;
mdm-power-gpios = <&gpiob 9 0>;
mdm-keep-awake-gpios = <&gpioc 2 0>;
mdm-reset-gpios = <&gpioc 12 0>;
mdm-shld-trans-ena-gpios = <&gpioc 4 0>;
status = "ok";
};
};