OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/boards/arc/arduino_101_sss/Kconfig.defconfig

34 lines
427 B
Plaintext
Raw Normal View History

build: switch to board based configurations Define boards based on platforms/SoCs and define them under boards/. Also unify the naming of all platform, SoC and board files and use platform.h for platforms and board.h for boards. Change-Id: Icfeb96479ab5800aca98c80a79bdc3cecd645314 Signed-off-by: Anas Nashif <anas.nashif@intel.com>
2015-12-13 22:31:16 +08:00
if BOARD_ARDUINO_101_SSS
config BOARD
Cleanup whitespace in Kconfig files Convert leading whitespace into tabs in Kconfig files. Also replaced double spaces between config and <prompt>. Change-Id: I341c718ecf4143529b477c239bbde88e18f37062 Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2016-05-25 07:17:13 +08:00
default "arduino_101_sss"
build: switch to board based configurations Define boards based on platforms/SoCs and define them under boards/. Also unify the naming of all platform, SoC and board files and use platform.h for platforms and board.h for boards. Change-Id: Icfeb96479ab5800aca98c80a79bdc3cecd645314 Signed-off-by: Anas Nashif <anas.nashif@intel.com>
2015-12-13 22:31:16 +08:00
arduino 101: make factory bootloader config the default The Arduino 101 comes with a bootloader that supports DFU and flashing of all cores using the dfu-util package. This changes the memory layout of the image built for the Arduino 101 and remove previous work-arounds to allow booting, including the version-header section in the linker script. The bootloader expects the text section at +0x30 from the physical load address and thus requires special treatment in the linker script. Other changes by Andrew Boie: The flash size parameters were both wrong. X86 side has 192K of flash from 0x4003000 - 0x40060000, the entire span of sys_flash1. ARC side is now the span from 0x40010000 - 0x40030000, 128K. Change-Id: Iecfa5d2b84a3f522d9eca06268d6b8b71a094aaa Signed-off-by: Anas Nashif <anas.nashif@intel.com>
2016-09-10 20:06:15 +08:00
config FLASH_SIZE
default 128
config FLASH_BASE_ADDRESS
default 0x40034000
drivers: spi_shim: grant arc the access to spi on I/O fabric Enable arc to access the spi controller on I/O fabric. There are two spi controllers on quark se SoC. One is attached to the I/O fabric and the other one is in the sensor system. X86 cpu is only able to access the spi controller on the I/O fabric and the access is supported by existing code. HW allows arc to access both controllers. But, the existing code only gives arc access to the controller in the sensor sub-system. Let's grant arc the access to the controller on I/O fabric as well by the following changes. 1. Add spi_qmsi.c into arc compilation. 2. Use the already defined macros to choose interrupt numbers and do interrupt unmasking automatically based on the compilation targets. 3. Add new symbols in Kconfig including driver names for both controllers Jira: ZEP-1190 Change-Id: I40a5d423d4b7986a897834d1a3831938005eda6f Signed-off-by: Baohong Liu <baohong.liu@intel.com>
2016-12-01 09:17:16 +08:00
if FLASH && SPI
config SPI_FLASH_W25QXXDV
def_bool y
config SPI_CS_GPIO
def_bool y
config SPI_0_CS_GPIO_PIN
default 24
config SPI_FLASH_W25QXXDV_SPI_NAME
default "SPI_0"
config SPI_FLASH_W25QXXDV_SPI_SLAVE
default 1
endif # FLASH && SPI
build: switch to board based configurations Define boards based on platforms/SoCs and define them under boards/. Also unify the naming of all platform, SoC and board files and use platform.h for platforms and board.h for boards. Change-Id: Icfeb96479ab5800aca98c80a79bdc3cecd645314 Signed-off-by: Anas Nashif <anas.nashif@intel.com>
2015-12-13 22:31:16 +08:00
endif # BOARD_ARDUINO_101_SSS