zephyr/boards/arduino/opta/arduino_opta_stm32h747xx_m7...

# Copyright (c) 2023 Felipe Neves
# Copyright (c) 2024 DNDG srl
# SPDX-License-Identifier: Apache-2.0

# Enable GPIO
CONFIG_GPIO=y

# Clock configuration
CONFIG_CLOCK_CONTROL=y

# Enable MPU
CONFIG_ARM_MPU=y

# Enable HW stack protection
CONFIG_HW_STACK_PROTECTION=y

# Use zephyr,code-partition as flash offset
CONFIG_USE_DT_CODE_PARTITION=y

# Enable correct power supply
CONFIG_POWER_SUPPLY_SMPS_1V8_SUPPLIES_EXT_AND_LDO=y

# Don't start M4 during the M7 boot (this is what the original Opta does)
CONFIG_STM32H7_BOOT_M4_AT_INIT=n

# Enable console
CONFIG_SERIAL=y
CONFIG_CONSOLE=y
CONFIG_UART_CONSOLE=y
CONFIG_UART_LINE_CTRL=y

# Enable USB Stack (needed for the console to work)
CONFIG_USB_DEVICE_STACK=y

# Enable regulator (needed to enable eth)
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED=y
boards: opta: initial support for M7 core Features enabled by this commit: * M7 core available with or without the Arduino MCU-based bootloader by correctly initializing the external clock source. * All LEDs, relays and the user button are mapped into the device tree (samples/common/blinky works out of the box). * USB can be used in ACM mode (samples/subsys/usb/cdc_acm works without changes). The default Zephyr console is configured to use cdc_acm_uart0 that in turn is assigned to the only USB port available. Also enable USB stack to make sure that the console is available by default and twister builds don't fail with missing device and added the default USB vendor (0x35d1 Finder SpA) and product (0x0164) numbers to match the ones used in the original product. Signed-off-by: Federico Di Gregorio <fog@dndg.it> 2024-08-19 22:23:34 +08:00			`# Copyright (c) 2023 Felipe Neves`
			`# Copyright (c) 2024 DNDG srl`
			`# SPDX-License-Identifier: Apache-2.0`

			`# Enable GPIO`
			`CONFIG_GPIO=y`

			`# Clock configuration`
			`CONFIG_CLOCK_CONTROL=y`

			`# Enable MPU`
			`CONFIG_ARM_MPU=y`

			`# Enable HW stack protection`
			`CONFIG_HW_STACK_PROTECTION=y`

			`# Use zephyr,code-partition as flash offset`
			`CONFIG_USE_DT_CODE_PARTITION=y`

			`# Enable correct power supply`
			`CONFIG_POWER_SUPPLY_SMPS_1V8_SUPPLIES_EXT_AND_LDO=y`

			`# Don't start M4 during the M7 boot (this is what the original Opta does)`
			`CONFIG_STM32H7_BOOT_M4_AT_INIT=n`

			`# Enable console`
			`CONFIG_SERIAL=y`
			`CONFIG_CONSOLE=y`
			`CONFIG_UART_CONSOLE=y`
			`CONFIG_UART_LINE_CTRL=y`

			`# Enable USB Stack (needed for the console to work)`
			`CONFIG_USB_DEVICE_STACK=y`
boards: opta: enable ethernet and RNG Features enabled by this commit: * RNG * Ethernet port (shell sample works without changes) Also fixed flash addresses in docs and added the default mapping between inputs and GPIO pins. Signed-off-by: Federico Di Gregorio <fog@dndg.it> 2024-09-06 18:28:22 +08:00
			`# Enable regulator (needed to enable eth)`
			`CONFIG_REGULATOR=y`
			`CONFIG_REGULATOR_FIXED=y`