OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/boards/arm/warp7_m4/dts_fixup.h

12 lines
863 B
C
Raw Normal View History

dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 22:15:23 +08:00
#define DT_FXOS8700_NAME DT_FSL_IMX7D_I2C_30A50000_NXP_FXOS8700_1E_LABEL
#define DT_FXOS8700_I2C_NAME DT_FSL_IMX7D_I2C_30A50000_NXP_FXOS8700_1E_BUS_NAME
#define DT_FXOS8700_I2C_ADDRESS DT_FSL_IMX7D_I2C_30A50000_NXP_FXOS8700_1E_BASE_ADDRESS
#define DT_FXOS8700_GPIO_NAME DT_FSL_IMX7D_I2C_30A50000_NXP_FXOS8700_1E_INT1_GPIOS_CONTROLLER
#define DT_FXOS8700_GPIO_PIN DT_FSL_IMX7D_I2C_30A50000_NXP_FXOS8700_1E_INT1_GPIOS_PIN
boards: Add support for WaRP7 board This patch is to add support for the WaRP7 board which has an i.MX7 Solo SoC. The Zephyr is running on the Cortex M4 core and the following features were validated on this board: * GPIO: User Switch detection and sensors interrupt * UART: Zephyr console * I2C: Communication with fxos8700 and fxas21002 sensors Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
2018-08-16 10:59:16 +08:00
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 22:15:23 +08:00
#define DT_FXAS21002_NAME DT_FSL_IMX7D_I2C_30A50000_NXP_FXAS21002_20_LABEL
#define DT_FXAS21002_I2C_NAME DT_FSL_IMX7D_I2C_30A50000_NXP_FXAS21002_20_BUS_NAME
#define DT_FXAS21002_I2C_ADDRESS DT_FSL_IMX7D_I2C_30A50000_NXP_FXAS21002_20_BASE_ADDRESS
#define DT_FXAS21002_GPIO_NAME DT_FSL_IMX7D_I2C_30A50000_NXP_FXAS21002_20_INT1_GPIOS_CONTROLLER
#define DT_FXAS21002_GPIO_PIN DT_FSL_IMX7D_I2C_30A50000_NXP_FXAS21002_20_INT1_GPIOS_PIN