OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/drivers/gpio/Kconfig.sam

12 lines
272 B
Plaintext
Raw Normal View History

kconfig: Clean up header comments and make them consistent Use this short header style in all Kconfig files: # <description> # <copyright> # <license> ... Also change all <description>s from # Kconfig[.extension] - Foo-related options to just # Foo-related options It's clear enough that it's about Kconfig. The <description> cleanup was done with this command, along with some manual cleanup (big letter at the start, etc.) git ls-files '*Kconfig*' | \ xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /' Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-11-01 20:45:29 +08:00
# Atmel SAM GPIO configuration options
drivers: GPIO Added GPIO for SAM family. Added GPIO driver for SAM family of SoCs. Signed-off-by: Justin Watson <jwatson5@gmail.com>
2018-03-03 08:14:16 +08:00
# Copyright (c) 2018 Justin Watson
# SPDX-License-Identifier: Apache-2.0
kconfig: Turn pointless/confusing 'menuconfig's into 'config's Defining a symbol with 'menuconfig' just tells the menuconfig to display any dependent symbols that immediately follow it in a separate menu. 'menuconfig' has no effect on symbol values. Making a symbol that doesn't have any dependent symbols after it a 'menuconfig' should be avoided, because then you end up with an empty menu, which is shown as e.g. [*] Enable foo --- This is how it would be shown if there were children but they all happened to be invisible as well. With a regular 'config', it turns into [*] Enable foo Change all pointless 'menuconfig's to 'config's. See the section on 'menuconfig' on the Kconfig - Tips and Best Practices page as well. Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-10-22 07:04:04 +08:00
config GPIO_SAM
drivers: GPIO Added GPIO for SAM family. Added GPIO driver for SAM family of SoCs. Signed-off-by: Justin Watson <jwatson5@gmail.com>
2018-03-03 08:14:16 +08:00
bool "Atmel SAM GPIO (PORT) driver"
soc: sam0: Enable generic peripheral selection Make sure that when e.g. CONFIG_SERIAL is set, CONFIG_UART_SAM0 is selected automatically when the sam0 SoC family is used. Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
2019-03-22 23:23:04 +08:00
default y
kconfig: gpio: Remove lots of redundant GPIO dependencies Most of these are from source'ing a file within an 'if GPIO', and then adding another 'depends on GPIO' within it. 'if FOO' is just shorthand for adding 'depends on FOO' to each item within the 'if'. There are no "conditional includes" in Kconfig, so 'if FOO' has no special meaning around a 'source'. Conditional includes wouldn't be possible, because an 'if' condition could include (directly or indirectly) forward references to symbols not defined yet. Tip: When adding a symbol, check its dependencies in the menuconfig ('ninja menuconfig', then / to jump to the symbol). The menuconfig also shows how the file with the symbol got included, so if you see duplicated dependencies, it's easy to hunt down where they come from. Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-03-07 14:12:27 +08:00
depends on SOC_FAMILY_SAM
drivers: GPIO Added GPIO for SAM family. Added GPIO driver for SAM family of SoCs. Signed-off-by: Justin Watson <jwatson5@gmail.com>
2018-03-03 08:14:16 +08:00
help
Enable support for the Atmel SAM 'PORT' GPIO controllers.