OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/drivers/w1/Kconfig

36 lines
578 B
Plaintext
Raw Normal View History

drivers: w1 introduce 1-wire api and common code This commit introduces a new api for the Dallas 1-wire protocol. The api includes link functions for read and write operations on bit, byte, and block level, as well as functions to reset and lock the bus. The bus configuration is derived from the device tree and can be queried using w1_slave_count routine. Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
2022-03-08 17:12:34 +08:00
# 1-Wire configuration options
# Copyright (c) 2022 Thomas Stranger
# SPDX-License-Identifier: Apache-2.0
menuconfig W1
bool
prompt "1-Wire Drivers"
help
Enable 1-Wire Drivers
if W1
module = W1
module-str = W1
source "subsys/logging/Kconfig.template.log_config"
config W1_INIT_PRIORITY
int
default 65
prompt "Init priority"
help
1-Wire device driver initialization priority.
drivers: w1: Add driver for Maxim DS2484 Single-Channel 1-Wire Master This adds a driver for Maxims DS2484 Single-Channel 1-Wire master driver. The DS2484 features an extra pin to enable sleep modes which is available if the pin is configured in the device tree. Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
2022-07-21 05:19:40 +08:00
rsource "Kconfig.ds2484"
drivers: w1: add vnd,w1 driver for ci testing This commit adds the vnd,w1 dummy host driver used for ci builds of 1-wire devices. Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
2022-03-06 19:19:09 +08:00
rsource "Kconfig.test"
drivers: w1: add zephyr-serial driver The zephyr-serial w1 driver introduced in this commit implements all routines for the w1 api on top of the zephyr serial driver. W1 bit read, write, and reset operations are executed by issuing polling zephyr serial byte read and write operations. The driver should be usable on most platforms in zephyr that have implemented support for the polling procedures of the serial driver. As not all serial drivers are implemented exactly the same minor additional quirks may be needed on some platforms. The most notable difference of polling serial driver implementations seems to be that some return immediately from poll_out after the transmission was started(e.g. STM32) and others wait until the transmission was completed before returning from poll_out (e.g. NRF). While this has influence on the timeout, both types are supported by this driver because the driver waits for a configurable time period until it terminates the read. The driver needs an appropriate open drain interface to be able to communicate with slaves. In the simpliest case this might be achived by configuring the mcu pins in open-drain configuration with a (sufficiently small) pull-up to 3V3/5V. Otherwise an external circuit needs to provide this interface. Overdrive and Standard Speed modes are supported by this driver. Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
2021-07-19 00:41:20 +08:00
rsource "Kconfig.zephyr_serial"
drivers: w1: add vnd,w1 driver for ci testing This commit adds the vnd,w1 dummy host driver used for ci builds of 1-wire devices. Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
2022-03-06 19:19:09 +08:00
drivers: w1 introduce 1-wire net layer api This commit introduces a new api for the net layer of Dallas 1-wire protocol. For single drop configurations w1_read_rom, and w1_skip_rom commands are provided. For multidrop configurations w1_match_rom, w1_resume_command, w1_search_rom, and w1_search_alarm routines are provided as well. Additionally, the reset_select routine, conditionally depending on the bus configuration, either executes a match_rom, or a skip rom command. A w1_write_read command simplifies the typical scenario of addressing a device, writing a few bytes to the device and reading back the answer. Additionally w1_crc8, and w1_crc16 are added as wrappers around the zephyr in-tree crc8 and crc16_reflect implementations. The former may be used to verify the validity of the rom id, while the latter is used for integrity checking of many eeprom, and authenticator commands. The general search command does not support filtering on the family code. Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
2022-07-04 02:00:23 +08:00
config W1_NET
bool "1-Wire network layer"
default y
help
Enable 1-wire network layer
drivers: w1 introduce 1-wire api and common code This commit introduces a new api for the Dallas 1-wire protocol. The api includes link functions for read and write operations on bit, byte, and block level, as well as functions to reset and lock the bus. The bus configuration is derived from the device tree and can be queried using w1_slave_count routine. Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
2022-03-08 17:12:34 +08:00
endif # W1