zephyr/boards/renesas/ek_ra8m1/ek_ra8m1.dts

/*
 * Copyright (c) 2024 Renesas Electronics Corporation
 * SPDX-License-Identifier: Apache-2.0
 */

/dts-v1/;

#include <renesas/ra/ra8/r7fa8m1ahecbd.dtsi>
#include <dt-bindings/gpio/gpio.h>
#include <zephyr/dt-bindings/adc/adc.h>
#include "ek_ra8m1-pinctrl.dtsi"

/ {
	model = "Renesas EK-RA8M1";
	compatible = "renesas,ra8m1", "renesas,ra8";

	chosen {
		zephyr,sram = &sram0;
		zephyr,flash = &flash0;
		zephyr,console = &uart9;
		zephyr,shell-uart = &uart9;
		zephyr,entropy = &trng;
	};

	leds {
		compatible = "gpio-leds";
		led1: led1 {
			gpios = <&ioport6 0 GPIO_ACTIVE_HIGH>;
			label = "LED1";
		};
		led2: led2 {
			gpios = <&ioport4 14 GPIO_ACTIVE_HIGH>;
			label = "LED2";
		};
		led3: led3 {
			gpios = <&ioport1 7 GPIO_ACTIVE_HIGH>;
			label = "LED3";
		};
	};

	mikrobus_header: mikrobus-connector {
		compatible = "mikro-bus";
		#gpio-cells = <2>;
		gpio-map-mask = <0xffffffff 0xffffffc0>;
		gpio-map-pass-thru = <0 0x3f>;
		gpio-map =	<0 0 &ioport0 4 0>,	/* AN  */
				<1 0 &ioport5 2 0>,	/* RST */
				<2 0 &ioport4 13 0>,	/* CS   */
				<3 0 &ioport4 12 0>,	/* SCK  */
				<4 0 &ioport4 10 0>,	/* MISO */
				<5 0 &ioport4 11 0>,	/* MOSI */
							/* +3.3V */
							/* GND */
				<6 0 &ioport9 7 0>,	/* PWM  */
				<7 0 &ioport0 10 0>,	/* INT  */
				<8 0 &ioport3 9 0>,	/* RX   */
				<9 0 &ioport3 10 0>,	/* TX   */
				<10 0 &ioport4 0 0>,	/* SCL  */
				<11 0 &ioport4 1 0>;	/* SDA  */
							/* +5V */
							/* GND */
	};

	aliases {
		led0 = &led1;
	};
};

&xtal {
	clock-frequency = <DT_FREQ_M(20)>;
	mosel = <0>;
	#clock-cells = <0>;
	status = "okay";
};

&subclk {
	status = "okay";
};

&pll {
	source = <RA_PLL_SOURCE_MAIN_OSC>;
	div = <RA_PLL_DIV_2>;
	mul = <96 0>;
	divp = <RA_PLL_DIV_2>;
	freqp = <DT_FREQ_M(480)>;
	divq = <RA_PLL_DIV_2>;
	freqq = <DT_FREQ_M(480)>;
	divr = <RA_PLL_DIV_2>;
	freqr = <DT_FREQ_M(480)>;
	status = "okay";
};

&sciclk {
	clk_src = <RA_CLOCK_SOURCE_PLL1P>;
	clk_div = <RA_SCI_CLOCK_DIV_4>;
	status = "okay";
};

&ioport0 {
	status = "okay";
};

&ioport1 {
	status = "okay";
};

&ioport3 {
	status = "okay";
};

&ioport4 {
	status = "okay";
};

&ioport5 {
	status = "okay";
};

&ioport6 {
	status = "okay";
};

&ioport9 {
	status = "okay";
};

&sci3 {
	pinctrl-0 = <&sci3_default>;
	pinctrl-names = "default";
	status = "okay";
	uart3: uart {
		current-speed = <115200>;
		status = "okay";
	};
};

&sci9 {
	pinctrl-0 = <&sci9_default>;
	pinctrl-names = "default";
	status = "okay";
	uart9: uart {
		current-speed = <115200>;
		status = "okay";
	};
};

mikrobus_serial: &uart3 {};

&iic1 {
	#address-cells = <1>;
	#size-cells = <0>;
	clock-frequency = <DT_FREQ_M(1)>;
	pinctrl-0 = <&iic1_default>;
	pinctrl-names = "default";
};

&adc0 {
	status = "okay";
	pinctrl-0 = <&adc0_default>;
	pinctrl-names = "default";
};

&trng {
	status = "okay";
};