OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/drivers/sensor/amg88xx/Kconfig

55 lines
1.1 KiB
Plaintext
Raw Normal View History

kconfig: Clean up header comments and make them consistent Use this short header style in all Kconfig files: # <description> # <copyright> # <license> ... Also change all <description>s from # Kconfig[.extension] - Foo-related options to just # Foo-related options It's clear enough that it's about Kconfig. The <description> cleanup was done with this command, along with some manual cleanup (big letter at the start, etc.) git ls-files '*Kconfig*' | \ xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /' Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-11-01 20:45:29 +08:00
# AMG88XX infrared thermopile sensor configuration options
drivers: sensors: add driver for amg88xx sensor This patch adds the driver for Panasonic AMG88xx infrared array sensor. The driver was developed within the framework of a student internship in the development department. The task of the student was to implement the trigger part of the driver, transfer and visualization of the measured data. Signed-off-by: Johann Fischer <j.fischer@phytec.de>
2017-09-25 23:38:33 +08:00
# Copyright (c) 2017 Phytec Messtechnik GmbH
# SPDX-License-Identifier: Apache-2.0
menuconfig AMG88XX
bool "AMG88XX Infrared Thermopile Sensor"
drivers: sensor: Update drivers to use devicetree Kconfig symbol Update sensor drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol to expose the driver and enable it by default based on devicetree. Signed-off-by: Kumar Gala <galak@kernel.org>
2022-07-20 11:41:45 +08:00
default y
depends on DT_HAS_PANASONIC_AMG88XX_ENABLED
drivers: sensor: Convert Kconfig bus 'depends on' to 'select' This change in pattern is meant to address a misconfiguration issue that can occur for sensors that support being on multiple busses like I2C & SPI. For example, you can have a configuration in which such a sensor is on the I2C bus in the devicetree and the sensor is enabled. However the application configuration enables CONFIG_SPI=y and CONFIG_I2C=n and this will cause the sensor driver to be built by default, however since we don't have the I2C bus enabled the driver will not compile correctly. Previously we had been adding to board Kconfig.defconfig something like: config I2C default y if SENSOR This pattern doesn't scale well and may differ from what an application specific need/use is. So instead move to a pattern in which we leave the default enablement up to the devicetree "status" property for the sensor. We then have the Kconfig move from 'depends on <BUS>' to 'select <BUS>' and in the case of drivers that support multiple busses we have the Kconfig be: 'select <BUS> if $(dt_compat_on_bus,$(<DT_COMPAT>),<BUS>) for each bus type the sensor supports. This removes the need to add Kconfig logic to each board and enables the bus subsystem and bus controller driver if the sensor requires it by default in the build system. Fixes: #48518 Signed-off-by: Kumar Gala <galak@kernel.org>
2022-08-04 23:55:31 +08:00
select I2C
drivers: sensors: add driver for amg88xx sensor This patch adds the driver for Panasonic AMG88xx infrared array sensor. The driver was developed within the framework of a student internship in the development department. The task of the student was to implement the trigger part of the driver, transfer and visualization of the measured data. Signed-off-by: Johann Fischer <j.fischer@phytec.de>
2017-09-25 23:38:33 +08:00
help
Enable driver for AMG88XX infrared thermopile sensor.
if AMG88XX
choice
prompt "Trigger mode"
default AMG88XX_TRIGGER_NONE
help
Specify the type of triggering used by the driver.
config AMG88XX_TRIGGER_NONE
bool "No trigger"
config AMG88XX_TRIGGER_GLOBAL_THREAD
bool "Use global thread"
depends on GPIO
select AMG88XX_TRIGGER
config AMG88XX_TRIGGER_OWN_THREAD
bool "Use own thread"
depends on GPIO
select AMG88XX_TRIGGER
endchoice
config AMG88XX_TRIGGER
bool
config AMG88XX_THREAD_PRIORITY
int "Thread priority"
depends on AMG88XX_TRIGGER_OWN_THREAD
default 10
help
Priority of thread used by the driver to handle interrupts.
config AMG88XX_THREAD_STACK_SIZE
int "Thread stack size"
depends on AMG88XX_TRIGGER_OWN_THREAD
default 1024
help
Stack size of thread used by the driver to handle interrupts.
kconfig: Global whitespace/consistency cleanup Clean up space errors and use a consistent style throughout the Kconfig files. This makes reading the Kconfig files more distraction-free, helps with grepping, and encourages the same style getting copied around everywhere (meaning another pass hopefully won't be needed). Go for the most common style: - Indent properties with a single tab, including for choices. Properties on choices work exactly the same syntactically as properties on symbols, so not sure how the no-indentation thing happened. - Indent help texts with a tab followed by two spaces - Put a space between 'config' and the symbol name, not a tab. This also helps when grepping for definitions. - Do '# A comment' instead of '#A comment' I tweaked Kconfiglib a bit to find most of the stuff. Some help texts were reflowed to 79 columns with 'gq' in Vim as well, though not all, because I was afraid I'd accidentally mess up formatting. Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-11-01 17:24:07 +08:00
endif # AMG88XX