OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/boards/arm/nucleo_l073rz/Kconfig.defconfig

36 lines
438 B
Plaintext
Raw Normal View History

kconfig: Clean up header comments and make them consistent Use this short header style in all Kconfig files: # <description> # <copyright> # <license> ... Also change all <description>s from # Kconfig[.extension] - Foo-related options to just # Foo-related options It's clear enough that it's about Kconfig. The <description> cleanup was done with this command, along with some manual cleanup (big letter at the start, etc.) git ls-files '*Kconfig*' | \ xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /' Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-11-01 20:45:29 +08:00
# STM32 Nucleo-64 development board with STM32L073RZ MCU
boards: arm: add NUCLEO-L073RZ board Add initial support for NUCLEO-L073RZ board. This is a typical Nucleo-64 board, so most files are reused from already supported Nucleo boards with small changes. Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
2018-03-11 23:27:12 +08:00
# Copyright (c) 2018 Ilya Tagunov <tagunil@gmail.com>
# SPDX-License-Identifier: Apache-2.0
if BOARD_NUCLEO_L073RZ
config BOARD
boards: defconfig: Consistently quote string defaults In preparation for introducing a warning. Unquoted string defaults work through a quirk of Kconfig (undefined symbols get their name as their string value), but look confusing. It's done inconsistently now too. Suggested by Kumar Gala. Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2018-05-26 02:56:38 +08:00
default "nucleo_l073rz"
boards: arm: add NUCLEO-L073RZ board Add initial support for NUCLEO-L073RZ board. This is a typical Nucleo-64 board, so most files are reused from already supported Nucleo boards with small changes. Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
2018-03-11 23:27:12 +08:00
if UART_CONSOLE
drivers/serial: stm32: Modify Kconfig instance flags STM32 uart Kconfig instance flags were not following same naming scheme than other drivers (i2c, spi, ..) Update driver to use UART_X instead of UART_STM32_PORT_X Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
2018-12-14 23:56:04 +08:00
config UART_2
boards: arm: add NUCLEO-L073RZ board Add initial support for NUCLEO-L073RZ board. This is a typical Nucleo-64 board, so most files are reused from already supported Nucleo boards with small changes. Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
2018-03-11 23:27:12 +08:00
default y
endif # UART_CONSOLE
boards: arm: nucleo_l073rz: add I2C support Enable I2C1 port according to silkscreen markings on Arduino header. Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
2018-03-14 00:27:31 +08:00
if I2C
config I2C_1
default y
boards: arm: nucleo_l073rz: add SPI support Enable SPI1 port according to silkscreen markings on Arduino header. Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
2018-03-15 20:29:36 +08:00
endif # I2C
if SPI
config SPI_1
default y
config SPI_STM32_INTERRUPT
default y
endif # SPI
boards: arm: nucleo_l073rz: add I2C support Enable I2C1 port according to silkscreen markings on Arduino header. Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
2018-03-14 00:27:31 +08:00
boards: arm: add NUCLEO-L073RZ board Add initial support for NUCLEO-L073RZ board. This is a typical Nucleo-64 board, so most files are reused from already supported Nucleo boards with small changes. Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
2018-03-11 23:27:12 +08:00
endif # BOARD_NUCLEO_L073RZ