OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/drivers/ethernet/Kconfig.adin2111

59 lines
1.7 KiB
Plaintext
Raw Permalink Normal View History

drivers: ethernet: add adin2111 Adds initial ADIN2111 2-Port 10BASE-T1L (SPE) switch support. Works over SPI. The driver creates 2 interfaces, 1 per port (PHY). Configures multicast and broadcast filters. The same unicast is applied to both ports. Supports: - Link state detection - CRC enable/disable - Ports config set - Ports ETH stats Provides functions for MDIO driver. Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
2023-05-12 20:49:53 +08:00
# Copyright (c) 2023 PHOENIX CONTACT Electronics GmbH
# SPDX-License-Identifier: Apache-2.0
menuconfig ETH_ADIN2111
bool "ADIN2111 2-port 10BASE-T1L Controller"
default y
drivers: ethernet: adin2111: add adin1110 support Add support for ADIN1110 10BASE-T1L Ethernet MAC-PHY. The ADIN1110 is an ultra low power, single port, 10BASE-T1L transceiver design for industrial Ethernet applications and is com- pliant with the IEEE® 802.3cg-2019™ Ethernet standard for long reach, 10 Mbps single pair Ethernet (SPE). Featuring an integrated media access control (MAC) interface, the ADIN1110 enables direct connectivity with a variety of host controllers via a 4-wire serial peripheral interface (SPI). This SPI enables the use of lower power processors without an integrated MAC, which provides for the lowest overall system level power consumption. The SPI can be configured to use the Open Alliance SPI protocol or a generic SPI protocol. Documentation: https://www.analog.com/en/products/adin1110.html Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
2023-07-20 16:48:05 +08:00
depends on DT_HAS_ADI_ADIN2111_ENABLED || DT_HAS_ADI_ADIN1110_ENABLED
drivers: ethernet: add adin2111 Adds initial ADIN2111 2-Port 10BASE-T1L (SPE) switch support. Works over SPI. The driver creates 2 interfaces, 1 per port (PHY). Configures multicast and broadcast filters. The same unicast is applied to both ports. Supports: - Link state detection - CRC enable/disable - Ports config set - Ports ETH stats Provides functions for MDIO driver. Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
2023-05-12 20:49:53 +08:00
select SPI
select MDIO
drivers: imply CRC where applicable Do not depend on CRC, imply it, as it is disabled by default now. Signed-off-by: Anas Nashif <anas.nashif@intel.com>
2023-08-17 02:01:51 +08:00
imply CRC
drivers: ethernet: add adin2111 Adds initial ADIN2111 2-Port 10BASE-T1L (SPE) switch support. Works over SPI. The driver creates 2 interfaces, 1 per port (PHY). Configures multicast and broadcast filters. The same unicast is applied to both ports. Supports: - Link state detection - CRC enable/disable - Ports config set - Ports ETH stats Provides functions for MDIO driver. Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
2023-05-12 20:49:53 +08:00
help
The ADIN2111 is a low power, 2-port 10BASE-T1L transceiver
designed for industrial Ethernet applications, and is compliant with
the IEEE® 802.3cg-2019™ Ethernet standard for long reach, 10
Mbps single pair Ethernet (SPE).
Featuring an integrated media access control (MAC) and a switch,
the ADIN2111 enables direct connectivity with a variety of controllers
via a serial peripheral inter-face (SPI).
if ETH_ADIN2111
config ETH_ADIN2111_IRQ_THREAD_STACK_SIZE
int "Stack size for a thread that processes ADIN IRQ"
default 2048
help
Size of the stack used for internal thread which is ran to
process raised INT IRQ.
config ETH_ADIN2111_IRQ_THREAD_PRIO
int "Priority for internal incoming packet handler"
default 2
help
Priority level for internal thread which is ran for ADIN
INT IRQ processing.
config ETH_ADIN2111_TIMEOUT
int "IP buffer timeout"
default 100
help
Given timeout in milliseconds. Maximum amount of time
that the driver will wait from the IP stack to get
a memory buffer before the Ethernet frame is dropped.
config ETH_ADIN2111_SPI_CFG0
bool "SPI_CFG0"
default y
help
Must be set when ADIN uses 8-bit CRC (Generic SPI)
or Protection Mode (OPEN Alliance) on the SPI Host Interface.
config ETH_ADIN2111_BUFFER_SIZE
int "Buffer size in bytes use for frame transmission"
default 1524
help
Transmission and reception buffer size.
endif # ETH_ADIN2111