97 lines
3.7 KiB
YAML
97 lines
3.7 KiB
YAML
# Licensed to the Apache Software Foundation (ASF) under one
|
|
# or more contributor license agreements. See the NOTICE file
|
|
# distributed with this work for additional information
|
|
# regarding copyright ownership. The ASF licenses this file
|
|
# to you under the Apache License, Version 2.0 (the
|
|
# "License"); you may not use this file except in compliance
|
|
# with the License. You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing,
|
|
# software distributed under the License is distributed on an
|
|
# "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY
|
|
# KIND, either express or implied. See the License for the
|
|
# specific language governing permissions and limitations
|
|
# under the License.
|
|
#
|
|
|
|
syscfg.defs:
|
|
BOOT_SERIAL_DETECT_PIN:
|
|
description: >
|
|
Start the serial boot loader if this pin is asserted at boot time.
|
|
value: '-1'
|
|
restrictions:
|
|
- '(BOOT_SERIAL_DETECT_PIN != -1) ||
|
|
(BOOT_SERIAL_DETECT_TIMEOUT != 0) ||
|
|
(BOOT_SERIAL_NVREG_INDEX != -1)'
|
|
|
|
BOOT_SERIAL_DETECT_PIN_CFG:
|
|
description: >
|
|
GPIO configuration for the serial boot loader detect pin.
|
|
value: 'HAL_GPIO_PULL_UP'
|
|
|
|
BOOT_SERIAL_DETECT_PIN_VAL:
|
|
description: >
|
|
The value the detect pin must be set to for the serial boot loader
|
|
to start.
|
|
value: 0
|
|
|
|
BOOT_SERIAL_DETECT_TIMEOUT:
|
|
description: >
|
|
The duration, in milliseconds, to listen on the UART for the
|
|
management string (BOOT_SERIAL_DETECT_STRING). If the management
|
|
string is detected during this period, the serial boot loader is
|
|
started. If the period expires without the management string being
|
|
received, the boot loader runs in the normal (non-serial) mode.
|
|
Specify 0 to disable listening on the UART for the management
|
|
string.
|
|
value: 0
|
|
restrictions:
|
|
- '(BOOT_SERIAL_DETECT_PIN != -1) ||
|
|
(BOOT_SERIAL_DETECT_TIMEOUT != 0) ||
|
|
(BOOT_SERIAL_NVREG_INDEX != -1)'
|
|
|
|
BOOT_SERIAL_DETECT_STRING:
|
|
description: >
|
|
The string to listen for on the UART. If this management string is
|
|
detected during the timeout period, the serial boot loader is
|
|
started. If the period expires without this string being received,
|
|
the boot loader runs in the normal (non-serial) mode. This setting
|
|
has no effect if BOOT_SERIAL_DETECT_TIMEOUT is set to 0.
|
|
value: '"nmgr"'
|
|
|
|
BOOT_SERIAL_REPORT_PIN:
|
|
description: >
|
|
The GPIO to toggle while the serial boot loader is running. Set to
|
|
-1 to disable reporting.
|
|
value: 'LED_BLINK_PIN'
|
|
|
|
BOOT_SERIAL_REPORT_FREQ:
|
|
description: >
|
|
The toggle rate, in Hz, of the serial boot loader report pin.
|
|
value: 4
|
|
|
|
BOOT_SERIAL_NVREG_MAGIC:
|
|
description: >
|
|
Magic number, to be saved in a retained (reset-surviving) register.
|
|
If the value in the register matches, the serial bootloader will
|
|
load. Value must not be 0.
|
|
value: 0xB7
|
|
restrictions:
|
|
- '(BOOT_SERIAL_NVREG_MAGIC != 0)'
|
|
|
|
BOOT_SERIAL_NVREG_INDEX:
|
|
description: >
|
|
Index of retained register to use (using hal_nvreg_read) for reading
|
|
magic value.
|
|
value: -1
|
|
restrictions:
|
|
- '(BOOT_SERIAL_DETECT_PIN != -1) ||
|
|
(BOOT_SERIAL_DETECT_TIMEOUT != 0) ||
|
|
(BOOT_SERIAL_NVREG_INDEX != -1)'
|
|
|
|
BOOT_SERIAL_MGMT_ECHO:
|
|
description: If enabled, support for the mcumgr echo command is being added.
|
|
value: 0
|