mcuboot/boot/cypress/BlinkyApp

Blinking LED test application for MCUBoot Bootloader

Description

Implements simple Blinky LED CM4 application to demonstrate MCUBoot Application operation in terms of BOOT and UPGRADE process.

It is started by MCUBoot Application which is running on CM0p.

Functionality:

• Blinks RED led with 2 different rates, depending on type of image - BOOT or UPGRADE.
• Prints debug info and version of itself to terminal at 115200 baud.
• Can be built for BOOT slot or UPGRADE slot of bootloader.

Currently supported platforms

• PSOC_062_2M

Hardware limitations

Since this application is created to demonstrate MCUBoot library features and not as reference examples some considerations are taken.

1. Port/pin P5_0 and P5_1 used to configure serial port for debug prints. These pins are the most commonly used for serial port connection among available Cypress PSoC 6 kits. If you try to use custom hardware with this application - change definitions of CY_DEBUG_UART_TX and CY_DEBUG_UART_RX in main.c of BlinkyApp to port/pin pairs corresponding to your design.
2. Port GPIO_PRT13 pin 7U used to define user connection LED. This pin is the most commonly used for USER_LED connection among available Cypress PSoC 6 kits. If you try to use custom hardware with this application - change definitions of LED_PORT and LED_PIN in main.c of BlinkyApp to port/pin pairs corresponding to your design.

Pre-build action

Pre-build action is implemented for defining start address and size of flash, as well as RAM start address and size for BlinkyApp. These values are set by specifing following macros: -DUSER_APP_SIZE, -DUSER_APP_START, -DRAM_SIZE, -DRAM_START in makefile.

Pre-build action calls GCC preprocessor which intantiates defines for particular values in BlinkyApp_template.ld.

Default values set for currently supported targets:

• PSOC_062_2M in BlinkyApp.mk to -DUSER_APP_START=0x10018000

Important: make sure RAM areas of CM4-based BlinkyApp and CM0p-based MCUBootApp bootloader do not overlap. Memory (stack) corruption of CM0p application can cause failure if SystemCall-served operations invoked from CM4.

Building an application

Root directory for build is boot/cypress.

The following command will build regular HEX file of a BlinkyApp for BOOT slot:

make app APP_NAME=BlinkyApp PLATFORM=PSOC_062_2M IMG_TYPE=BOOT

This have following defaults suggested:

BUILDCFG=Debug
IMG_TYPE=BOOT

To build UPGRADE image use following command:

make app APP_NAME=BlinkyApp PLATFORM=PSOC_062_2M IMG_TYPE=UPGRADE HEADER_OFFSET=0x10000

Note: HEADER_OFFSET=%SLOT_SIZE%

Example command-line for single-image:

make app APP_NAME=BlinkyApp PLATFORM=PSOC_062_2M IMG_TYPE=BOOT

Building Multi-Image

BlinkyApp can be built to use in multi-image bootloader configuration.

To get appropriate artifacts to use with multi image MCUBootApp, makefile flag HEADER_OFFSET= can be used.

Example usage:

Considering default config:

• first image BOOT (PRIMARY) slot start 0x10018000
• slot size 0x10000
• second image BOOT (PRIMARY) slot start 0x10038000

To get appropriate artifact for second image PRIMARY slot run this command:

make app APP_NAME=BlinkyApp PLATFORM=PSOC_062_2M IMG_TYPE=BOOT HEADER_OFFSET=0x20000

Note: only 2 images are supported at the moment.

How to build upgrade image for external memory:

To prepare MCUBootApp for work with external memory please refer to MCUBootApp/ExternalMemory.md.

For build BlinkyApp upgarde image for external memory use command:

make app APP_NAME=BlinkyApp PLATFORM=PSOC_062_2M IMG_TYPE=UPGRADE HEADER_OFFSET=0x7FE8000 ERASED_VALUE=0xff

HEADER_OFFSET defines the offset from original boot image address. This one in line above suggests secondary slot will start from 0x18000000.

ERASED_VALUE defines the memory cell contents in erased state. It is 0x00 for PSoC6's internal Flash and 0xff for S25FL512S.

In case of using muti-image configuration, upgrade image for second application can be built using next command:

make app APP_NAME=BlinkyApp PLATFORM=PSOC_062_2M IMG_TYPE=UPGRADE HEADER_OFFSET=0x8028000 ERASED_VALUE=0xff

Note: for S25FL512S block address shuld be mutiple by 0x40000

Post-Build

Post build action is executed at compile time for BlinkyApp. In case of build for PSOC_062_2M platform it calls imgtool from MCUBoot scripts and adds signature to compiled image.

Flags passed to imgtool for signature are defined in SIGN_ARGS variable in BlinkyApp.mk.

How to program an application

Use any preferred tool for programming hex files.

Hex file names to use for programming:

BlinkyApp always produce build artifacts in 2 separate folders - boot and upgrade.

BlinkyApp built to run with MCUBootApp produces files with name BlinkyApp.hex in boot directory and BlinkyApp_upgrade.hex in upgrade folder. These files are ready to be flashed to the board.

BlinkyApp_unsigned.hex hex file is also preserved in both cases for possible troubleshooting.

Files to use for programming are:

BOOT - boot/BlinkyApp.hex UPGRADE - upgrade/BlinkyApp_upgrade.hex

Flags:

• BUILDCFG - configuration Release or Debug
• MAKEINFO - 0 (default) - less build info, 1 - verbose output of compilation.
• HEADER_OFFSET - 0 (default) - no offset of output hex file, 0x%VALUE% - offset for output hex file. Value 0x10000 is slot size MCUBoot Bootloader in this example.
• IMG_TYPE - BOOT (default) - build image for BOOT slot of MCUBoot Bootloader, UPGRADE - build image for UPGRADE slot of MCUBoot Bootloader.

NOTE: In case of UPGRADE image HEADER_OFFSET should be set to MCUBoot Bootloader slot size.

Example terminal output

When user application programmed in BOOT slot:

===========================
[BlinkyApp] BlinkyApp v1.0 [CM4]
===========================
[BlinkyApp] GPIO initialized
[BlinkyApp] UART initialized
[BlinkyApp] Retarget I/O set to 115200 baudrate
[BlinkyApp] Red led blinks with 1 sec period

When user application programmed in UPRADE slot and upgrade procedure was successful:

===========================
[BlinkyApp] BlinkyApp v2.0 [+]
===========================

[BlinkyApp] GPIO initialized
[BlinkyApp] UART initialized
[BlinkyApp] Retarget I/O set to 115200 baudrate
[BlinkyApp] Red led blinks with 0.25 sec period