Introduced MCUBOOT_CPU_IDLE() macro.
If a port supports single thread or is bare-metal then might be need
to switch to idle mode explicitly form MCUboot code.
The call allows to enable lower power consumption while waiting for
incoming transmission in serial recovery etc.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The 'revert' mechanism in direct-xip is similar to the one in swap mode.
It requires the trailer magic to be added to the signed image. When a
reboot happens without the image being confirmed at runtime (without the
image_ok flag being set), the bootloader considers the image faulty and
erases it. After this it will attempt to boot the previous image
instead. The images can also be made permanent (marked as confirmed in
advance) just like in swap mode.
Change-Id: Ibde9361d4a7302dd8efbb277b691b71eca0ca877
Signed-off-by: David Vincze <david.vincze@linaro.org>
This patch introduces the ram-load mode in addition to the other
upgrade modes (swap strategies, overwrite-only, direct-XIP). When
ram-load is enabled with the MCUBOOT_RAM_LOAD option, mcuboot
selects the newest valid image based on the image version numbers from
the image header, thereafter the selected image loaded to the RAM and
executed from there. Load address is extracted from the image header.
Therefore the images must be linked to the RAM memory region.
The ram-load mode is very similar to the direct-XIP mode, main
difference is to load the newest image to the RAM beforehand the
authentication and execution. Similar to direct-XIP mode either
of the primary and the secondary slots can hold the active image.
Ram-load can be useful in case of a bit more powerful SoC, which
is not constrained in terms of internal RAM. It could be that image
is stored in external and therefore untrusted flash. Loading image
to internal (trusted) RAM is essential from the security point
of view the system. Furthermore execution from internal RAM is much
faster than from external flash.
This patch is based on the RAM_LOADING upgrade strategy which was
first introduced in the Trusted Firmware-M project.
Source TF-M version: TF-Mv1.0.
Change-Id: I95f02ff07c1dee51244ac372284f449c2efab362
Signed-off-by: Tamas Ban <tamas.ban@arm.com>
This patch introduces the direct execute-in-place (XIP) mode in addition
to the other upgrade modes (swap strategies, overwrite-only). When
direct-XIP is enabled with the MCUBOOT_DIRECT_XIP option, mcuboot
selects the newest valid image based on the image version numbers from
the image header, thereafter the selected image runs directly from its
flash partition (slot) instead of moving it. Therefore the images must
be linked to be executed from the given image slot. It means that in
direct-XIP mode either of the primary and the secondary slots can hold
the active image.
This patch is based on the NO_SWAP upgrade strategy which was first
introduced in the Trusted Firmware-M project.
Source TF-M version: TF-Mv1.0.
Change-Id: If584cf01ae5aa7208845f6a6fa206f0595e0e61e
Signed-off-by: David Vincze <david.vincze@linaro.org>
This patch introduces the BOOT_IMAGE_NUMBER macro and current_image
variable to support multiple updatable images and the associated
extended flash layout.
The FLASH_AREA_IMAGE_* object-like macros are replaced with
function-like ones and therefore some functions have been updated,
because the labels of a switch statement and the initialization
values of objects with static storage duration have to be constant
expressions.
Change-Id: Ib7b26ec3c94233e52db4f97825ddb6a3e55bb1d3
Signed-off-by: David Vincze <david.vincze@arm.com>
When HW / OS provides an always enabled watchdog, this macro can
optionally be implemented to avoid resets which are expected to
occur under normal conditions when swapping very large images or
running on slower devices.
Signed-off-by: Fabio Utzig <utzig@apache.org>
This change replaces the slot 0/1 terminology with primary/secondary
slot and replaces FLASH_AREA_IMAGE_0/1 with
FLASH_AREA_IMAGE_PRIMARY/SECONDARY. This naming convention may be more
understandable, fits better to MCUs with multiple images and it is an
architecture agnostic alternative as well.
Change-Id: I655a585f6ae023852c671ee6635399efe25209c9
Signed-off-by: David Vincze <david.vincze@arm.com>
Signed-off-by: David Brown <david.brown@linaro.org>
Introduce MCUBOOT_LOG_MODULE_REGISTER and MCUBOOT_LOG_MODULE_DECLARE.
- MCUBOOT_LOG_MODULE_REGISTER
Register a new log module and add the current C file to it.
- MCUBOOT_LOG_MODULE_DECLARE
Add the current C file to an existing log module.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
- Removed MCUBOOT_LOG_LEVEL macros.
The global log level shall be set using a port's configuration
management system of choice instead e.g Kconfig.
- Removed BOOT_LOG_LEVEL macro, which was not honored by
either Zephyr or mynewt ports.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Continue removing platform-specific conditional compilation from
bootutil by adding a new MCUBOOT_HAVE_ASSERT_H configuration option
and associated header file. Right now, that's only used by the
simulator.
That leaves just bootutil_log.h with platform-specific contents, but
since it's meant to be an abstraction layer for logging, we'll let it
stand for now.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Take the opportunity to clean up a bit of platform cruft that has
gotten into bootutil by moving it to mcuboot_config.h, and ensuring it
is documented in the template config file.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Mynewt uses this file to convert MYNEWT_VAL(xxx) to MCUBOOT_xxx config
options. Zephyr currently adds config options via the compiler command
line, but it should use this instead.
As prep work for that conversion, add an empty mcuboot_config.h to the
Zephyr port, and include this file unconditionally wherever it's
needed. This takes care of the simulator as well, since that puts
boot/zephyr/include on its C file include path.
This turned up a couple of files (bootutil_priv.h and caps.c) that
were using the MCUBOOT_xxx config values without including the
file. Add the includes there, as they'll be needed later.
To make this official, add it to the requirements in the porting guide
and provide a template file porters can use while getting started.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
fixup! Mandate the presence of mcuboot_config/mcuboot_config.h
Andrzej Puzdrowski