/**
@page Camera_To_USBDisk Camera to USB Disk application
@verbatim
******************************************************************************
* @file Camera/Camera_To_USBDisk/readme.txt
* @author MCD Application Team
* @brief Description of the Camera to USB Disk application.
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
* @attention
*
* Copyright (c) 2016 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Application Description
This application provides a short description of how to use the DCMI to interface with
camera module and display in continuous mode the picture on LCD and to save a picture
in USB device.
At the beginning of the main program the HAL_Init() function is called to reset
all the peripherals, initialize the Flash interface and the systick.
Then the SystemClock_Config() function is used to configure the system
clock (SYSCLK) to run at 200 MHz.
The Digital camera interface is configured to receive the capture from
the camera module mounted on STM32F769I_EVAL evaluation board.
DMA2 Stream1 channel1 is configured to transfer the picture from DCMI peripheral
to an external RAM used by the LCD as a frame buffer.
The camera module is configured to generate (480x272) image resolution
and the LCD is configured to display in resolution WVGA(800x480) in orientation landscape.
When the tamper button is pressed an image is saved under USBdisk.
- LED1 is on to indicate the end of saving operation and a message is displayed
on LCD to indicate the beginning and the end of the saving operation.
- LED3 is ON when any error occurs.
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Keywords
Display, Camera, USB Disk, DCMI, LCD, DMA, Frame buffer, WVGA
@Note<74>If the user code size exceeds the DTCM-RAM size or starts from internal cacheable memories (SRAM1 and SRAM2),that is shared between several processors,
<20><><A0><A0><A0>then it is highly recommended to enable the CPU cache and maintain its coherence at application level.
<0A><><A0><A0><A0><A0>The address and the size of cacheable buffers (shared between CPU and other masters) must be properly updated to be aligned to cache line size (32 bytes).
@Note It is recommended to enable the cache and maintain its coherence, but depending on the use case
<0A><><A0><A0><A0> It is also possible to configure the MPU as "Write through", to guarantee the write access coherence.
<0A><><A0><A0><A0><A0>In that case, the MPU must be configured as Cacheable/Bufferable/Not Shareable.
<0A><><A0><A0><A0><A0>Even though the user must manage the cache coherence for read accesses.
<0A><><A0><A0><A0><A0>Please refer to the AN4838 <20>Managing memory protection unit (MPU) in STM32 MCUs<55>
<0A><><A0><A0><A0><A0>Please refer to the AN4839 <20>Level 1 cache on STM32F7 Series<65>
@par Directory contents
- Camera/Camera_To_USBDisk/Inc/stm32f7xx_hal_conf.h HAL configuration file
- Camera/Camera_To_USBDisk/Inc/main.h Main program header file
- Camera/Camera_To_USBDisk/Inc/stm32f7xx_it.h Interrupt handlers header file
- Camera/Camera_To_USBDisk/Inc/ffconf.h FAT file system module configuration file
- Camera/Camera_To_USBDisk/Inc/usbh_conf.h Header for usbh_conf.c
- Camera/Camera_To_USBDisk/Src/usbh_diskio.h USB host diskio header file
- Camera/Camera_To_USBDisk/Src/main.c Main program
- Camera/Camera_To_USBDisk/Src/stm32f7xx_it.c Interrupt handlers
- Camera/Camera_To_USBDisk/Src/system_stm32f7xx.c STM32F7xx system clock configuration file
- Camera/Camera_To_USBDisk/Src/usbh_conf.c USB configuration file.
- Camera/Camera_To_USBDisk/Src/usbh_diskio.c USB host diskio file
@par Hardware and Software environment
- This application runs on STM32F769xx and STM32F779xx devices.
- This application has been tested with STM32F769I-EVAL board which includes
the KoD DSI LCD and S5K5CAG camera module.
- STM32F769I-EVAL Set-up
- Plug the USB key into the STM32F769I-EVAL board through 'USB micro A-Male
to A-Female' cable (HS mode: connector CN8).
- Make sure jumper JP10 of STM32F769I-EVAL board is not fitted.
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the application
*/
767d083e20