/**
@page MSC_Standalone USB Device Mass Storage (MSC) application
@verbatim
******************************************************************************
* @file USB_Device/MSC_Standalone/readme.txt
* @author MCD Application Team
* @brief Description of the USB Device MSC application.
******************************************************************************
*
* @attention
*
* Copyright (c) 2017 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Application Description
Use of the USB device application based on the Mass Storage Class (MSC).
This is a typical application on how to use the STM32F7xx USB OTG Device peripheral to communicate with a PC
Host using the Bulk Only Transfer (BOT) and Small Computer System Interface (SCSI) transparent commands,
while the microSD card is used as storage media. The STM32 MCU is enumerated as a MSC device using the
native PC Host MSC driver to which the STM32F769I-Discovery board is connected.
At the beginning of the main program the HAL_Init() function is called to reset all the peripherals,
initialize the Flash interface and the systick. The user is provided with the SystemClock_Config()
function to configure the system clock (SYSCLK) to run at 216 MHz. The Full Speed (FS) USB module uses
internally a 48-MHz clock which is coming from a specific output of two PLLs: main PLL or PLL SAI.
In the High Speed (HS) mode the USB clock (60 MHz) is driven by the ULPI.
When the application is started, the user has just to plug the USB cable into a PC host and the device
is automatically detected. A new removable drive appears in the system window and write/read/format
operations can be performed as with any other removable drive.
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
For more details about the STM32Cube USB Device library, please refer to UM1734
"STM32Cube USB Device library".
@par Keywords
Connectivity, USB_Device, USB, MSC, Mass Storage, Full Speed, High Speed, BOT, SCSI, SD Card, Removable drive,
Write, Read, Format
@Note<74>If the user code size exceeds the DTCM-RAM size or starts from internal cacheable memories (SRAM1 and SRAM2),that is shared between several processors,
<20><><A0><A0><A0>then it is highly recommended to enable the CPU cache and maintain its coherence at application level.
<0A><><A0><A0><A0><A0>The address and the size of cacheable buffers (shared between CPU and other masters) must be properly updated to be aligned to cache line size (32 bytes).
@Note It is recommended to enable the cache and maintain its coherence, but depending on the use case
<0A><><A0><A0><A0> It is also possible to configure the MPU as "Write through", to guarantee the write access coherence.
<0A><><A0><A0><A0><A0>In that case, the MPU must be configured as Cacheable/Bufferable/Not Shareable.
<0A><><A0><A0><A0><A0>Even though the user must manage the cache coherence for read accesses.
<0A><><A0><A0><A0><A0>Please refer to the AN4838 <20>Managing memory protection unit (MPU) in STM32 MCUs<55>
<0A><><A0><A0><A0><A0>Please refer to the AN4839 <20>Level 1 cache on STM32F7 Series<65>
@par Directory contents
- USB_Device/MSC_Standalone/Src/main.c Main program
- USB_Device/MSC_Standalone/Src/system_stm32f7xx.c STM32F7xx system clock configuration file
- USB_Device/MSC_Standalone/Src/stm32f7xx_it.c Interrupt handlers
- USB_Device/MSC_Standalone/Src/usbd_conf.c General low level driver configuration
- USB_Device/MSC_Standalone/Src/usbd_desc.c USB device MSC descriptor
- USB_Device/MSC_Standalone/Src/ubsd_storage.c Media Interface Layer
- USB_Device/MSC_Standalone/Inc/main.h Main program header file
- USB_Device/MSC_Standalone/Inc/stm32f7xx_it.h Interrupt handlers header file
- USB_Device/MSC_Standalone/Inc/stm32f7xx_hal_conf.h HAL configuration file
- USB_Device/MSC_Standalone/Inc/usbd_conf.h USB device driver Configuration file
- USB_Device/MSC_Standalone/Inc/usbd_desc.h USB device MSC descriptor header file
- USB_Device/MSC_Standalone/Inc/ubsd_storage.h Media Interface Layer header file
@par Hardware and Software environment
- This application runs on STM32F767xx/STM32F769xx/STM32F777xx/STM32F779xx devices.
- This application has been tested with STMicroelectronics STM32F769I-Discovery
boards and can be easily tailored to any other supported device
and development board.
- STM32F769I-Discovery Set-up
- Insert a microSD card into the STM32F769I-Discovery uSD slot (CN5)
- Connect the STM32F769I-Discovery board to the PC through 'USB micro A-Male
to A-Male' cable to the connector:
- CN15 : to use USB High Speed (HS)
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- In the workspace toolbar select the project configuration:
- STM32F769I-Discovery-HS: to configure the project for STM32F7xx devices using USB OTG HS peripheral
- Run the application
*/
767d083e20