104 lines
4.7 KiB
Plaintext
104 lines
4.7 KiB
Plaintext
/**
|
||
@page DMA_FLASHToRAM DMA FLASH To RAM Example
|
||
|
||
@verbatim
|
||
******************************************************************************
|
||
* @file DMA/DMA_FLASHToRAM/readme.txt
|
||
* @author MCD Application Team
|
||
* @brief Description of the DMA FLASH to RAM example.
|
||
******************************************************************************
|
||
* @attention
|
||
*
|
||
* Copyright (c) 2016 STMicroelectronics.
|
||
* All rights reserved.
|
||
*
|
||
* This software is licensed under terms that can be found in the LICENSE file
|
||
* in the root directory of this software component.
|
||
* If no LICENSE file comes with this software, it is provided AS-IS.
|
||
*
|
||
******************************************************************************
|
||
@endverbatim
|
||
|
||
@par Example Description
|
||
|
||
How to use a DMA to transfer a word data buffer from Flash memory to embedded
|
||
SRAM through the HAL API.
|
||
|
||
At the beginning of the main program the HAL_Init() function is called to reset
|
||
all the peripherals, initialize the Flash interface and the systick.
|
||
Then the SystemClock_Config() function is used to configure the system
|
||
clock (SYSCLK) to run at 216 MHz.
|
||
|
||
DMA2_Stream0 is configured to transfer the contents of a 32-word data
|
||
buffer stored in Flash memory to the reception buffer declared in RAM.
|
||
|
||
The start of transfer is triggered by software. DMA2_Stream0 memory-to-memory
|
||
transfer is enabled. Source and destination addresses incrementing is also enabled.
|
||
The transfer is started by setting the stream enable bit for DMA2_Stream0.
|
||
At the end of the transfer a Transfer Complete interrupt is generated since it
|
||
is enabled and the callback function (customized by user) is called.
|
||
|
||
|
||
Board's LEDs can be used to monitor the transfer status:
|
||
- LED1 is ON when the transfer is complete (into the Transfer Complete interrupt
|
||
routine).
|
||
- LED1 is Toggled with a period of 200 ms when there is a transfer error
|
||
- LED1 is Toggled with a period of 1000 ms when Error_Handler is called
|
||
|
||
It is possible to select a different stream for the DMA transfer
|
||
example by modifying defines values in the file main.h.
|
||
Note that only DMA2 stream are able to perform Memory-to-Memory transfers.
|
||
|
||
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
||
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
||
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
||
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
||
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
||
|
||
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
||
to have correct HAL operation.
|
||
|
||
@par Keywords
|
||
|
||
System, DMA, Data Transfer, Memory to memory, Stream, Flash, RAM
|
||
|
||
@Note<74>If the user code size exceeds the DTCM-RAM size or starts from internal cacheable memories (SRAM1 and SRAM2),that is shared between several processors,
|
||
<20><><EFBFBD><EFBFBD><EFBFBD>then it is highly recommended to enable the CPU cache and maintain its coherence at application level.
|
||
<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>The address and the size of cacheable buffers (shared between CPU and other masters) must be properly updated to be aligned to cache line size (32 bytes).
|
||
|
||
@Note It is recommended to enable the cache and maintain its coherence, but depending on the use case
|
||
<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD> It is also possible to configure the MPU as "Write through", to guarantee the write access coherence.
|
||
<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>In that case, the MPU must be configured as Cacheable/Bufferable/Not Shareable.
|
||
<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>Even though the user must manage the cache coherence for read accesses.
|
||
<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>Please refer to the AN4838 <20>Managing memory protection unit (MPU) in STM32 MCUs<55>
|
||
<EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD><EFBFBD>Please refer to the AN4839 <20>Level 1 cache on STM32F7 Series<65>
|
||
|
||
@par Directory contents
|
||
|
||
- DMA/DMA_FLASHToRAM/Src/system_stm32f7xx.c STM32F7xx system clock configuration file
|
||
- DMA/DMA_FLASHToRAM/Src/stm32f7xx_it.c Interrupt handlers
|
||
- DMA/DMA_FLASHToRAM/Src/main.c Main program
|
||
- DMA/DMA_FLASHToRAM/Inc/stm32f7xx_hal_conf.h HAL Configuration file
|
||
- DMA/DMA_FLASHToRAM/Inc/stm32f7xx_it.h Interrupt handlers header file
|
||
- DMA/DMA_FLASHToRAM/Inc/main.h Main program header file
|
||
|
||
|
||
@par Hardware and Software environment
|
||
|
||
- This example runs on STM32F756xx/STM32F746xx Devices.
|
||
|
||
- This example has been tested with STMicroelectronics STM32746G-DISCOVERY
|
||
evaluation boards and can be easily tailored to any other supported device
|
||
and development board.
|
||
|
||
@par How to use it ?
|
||
|
||
In order to make the program work, you must do the following :
|
||
- Open your preferred toolchain
|
||
- Rebuild all files and load your image into target memory
|
||
- Run the example
|
||
|
||
|
||
|
||
*/
|