/**
@page ADC_RegularConversion_DMA conversion using DMA for Data transfer
@verbatim
******************************************************************************
* @file ADC/ADC_RegularConversion_DMA/readme.txt
* @author MCD Application Team
* @brief Description of the ADC RegularConversion DMA example.
******************************************************************************
* @attention
*
* Copyright (c) 2016 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Example Description
How to use the ADC3 and DMA to transfer continuously converted data from
ADC3 to memory.
The ADC3 is configured to convert continuously ADC_CHANNEL_8.
Each time an end of conversion occurs the DMA transfers, in circular mode, the
converted data from ADC3 DR register to the uhADCxConvertedValue variable.
The uhADCxConvertedValue read value is coded on 12 bits, the Vref+ reference voltage is connected
on the board to VDD (+3.3V), the Vref- reference voltage is connected on the board to the ground.
To convert the read value in volts, here is the equation to apply :
Voltage = uhADCxConvertedValue * (Vref+ - Vref-) / (2^12) = uhADCxConvertedValue * 3.3 / 4096
In this example, the system clock is 216MHz, APB2 = 108MHz and ADC clock = APB2/4.
Since ADC3 clock is 27 MHz and sampling time is set to 3 cycles, the conversion
time to 12bit data is 12 cycles so the total conversion time is (12+3)/27 = 0.56us(1.57Msps).
User can vary the ADC_CHANNEL_8 voltage by applying an input voltage on pin PF10 connected to Arduino CN5 pin A1.
STM32 Eval board's LEDs can be used to monitor the transfer status:
- LED1 is ON when the conversion is complete.
- LED1 blinks when error occurs in initialization.
@par Keywords
Analog, ADC, Analog to Digital Converter, Regular Conversion, DMA, Continuous Conversion
@Note<74>If the user code size exceeds the DTCM-RAM size or starts from internal cacheable memories (SRAM1 and SRAM2),that is shared between several processors,
<20><><A0><A0><A0>then it is highly recommended to enable the CPU cache and maintain its coherence at application level.
<0A><><A0><A0><A0><A0>The address and the size of cacheable buffers (shared between CPU and other masters) must be properly updated to be aligned to cache line size (32 bytes).
@Note It is recommended to enable the cache and maintain its coherence, but depending on the use case
<0A><><A0><A0><A0> It is also possible to configure the MPU as "Write through", to guarantee the write access coherence.
<0A><><A0><A0><A0><A0>In that case, the MPU must be configured as Cacheable/Bufferable/Not Shareable.
<0A><><A0><A0><A0><A0>Even though the user must manage the cache coherence for read accesses.
<0A><><A0><A0><A0><A0>Please refer to the AN4838 <20>Managing memory protection unit (MPU) in STM32 MCUs<55>
<0A><><A0><A0><A0><A0>Please refer to the AN4839 <20>Level 1 cache on STM32F7 Series<65>
@par Directory contents
- ADC/ADC_RegularConversion_DMA/Inc/stm32f7xx_hal_conf.h HAL configuration file
- ADC/ADC_RegularConversion_DMA/Inc/stm32f7xx_it.h DMA interrupt handlers header file
- ADC/ADC_RegularConversion_DMA/Inc/main.h Header for main.c module
- ADC/ADC_RegularConversion_DMA/Src/stm32f7xx_it.c DMA interrupt handlers
- ADC/ADC_RegularConversion_DMA/Src/main.c Main program
- ADC/ADC_RegularConversion_DMA/Src/stm32f7xx_hal_msp.c HAL MSP file
- ADC/ADC_RegularConversion_DMA/Src/system_stm32f7xx.c STM32F7xx system source file
@par Hardware and Software environment
- This example runs on STM32F7xx devices.
- This example has been tested with STM32746G-DISCOVERY board and can be
easily tailored to any other supported device and development board.
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
*/
767d083e20