/** ****************************************************************************** * @file stm32f7xx_hal_conf.h * @author MCD Application Team * @brief HAL configuration file. ****************************************************************************** * @attention * * Copyright (c) 2016 STMicroelectronics. * All rights reserved. * * This software is licensed under terms that can be found in the LICENSE file * in the root directory of this software component. * If no LICENSE file comes with this software, it is provided AS-IS. * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef __STM32F7xx_HAL_CONF_H #define __STM32F7xx_HAL_CONF_H #ifdef __cplusplus extern "C" { #endif /* Exported types ------------------------------------------------------------*/ /* Exported constants --------------------------------------------------------*/ /* ########################## Module Selection ############################## */ /** * @brief This is the list of modules to be used in the HAL driver */ #define HAL_MODULE_ENABLED #define HAL_ADC_MODULE_ENABLED #define HAL_CAN_MODULE_ENABLED /* #define HAL_CAN_LEGACY_MODULE_ENABLED */ #define HAL_CEC_MODULE_ENABLED #define HAL_CRC_MODULE_ENABLED #define HAL_CRYP_MODULE_ENABLED #define HAL_DAC_MODULE_ENABLED #define HAL_DCMI_MODULE_ENABLED #define HAL_DMA_MODULE_ENABLED #define HAL_DMA2D_MODULE_ENABLED #define HAL_ETH_MODULE_ENABLED #define HAL_EXTI_MODULE_ENABLED #define HAL_FLASH_MODULE_ENABLED #define HAL_NAND_MODULE_ENABLED #define HAL_NOR_MODULE_ENABLED #define HAL_SRAM_MODULE_ENABLED #define HAL_SDRAM_MODULE_ENABLED #define HAL_HASH_MODULE_ENABLED #define HAL_GPIO_MODULE_ENABLED #define HAL_I2C_MODULE_ENABLED #define HAL_I2S_MODULE_ENABLED #define HAL_IWDG_MODULE_ENABLED #define HAL_LPTIM_MODULE_ENABLED #define HAL_LTDC_MODULE_ENABLED #define HAL_PWR_MODULE_ENABLED #define HAL_QSPI_MODULE_ENABLED #define HAL_RCC_MODULE_ENABLED #define HAL_RNG_MODULE_ENABLED #define HAL_RTC_MODULE_ENABLED #define HAL_SAI_MODULE_ENABLED #define HAL_SD_MODULE_ENABLED #define HAL_SPDIFRX_MODULE_ENABLED #define HAL_SPI_MODULE_ENABLED #define HAL_TIM_MODULE_ENABLED #define HAL_UART_MODULE_ENABLED #define HAL_USART_MODULE_ENABLED #define HAL_IRDA_MODULE_ENABLED #define HAL_SMARTCARD_MODULE_ENABLED #define HAL_WWDG_MODULE_ENABLED #define HAL_CORTEX_MODULE_ENABLED #define HAL_PCD_MODULE_ENABLED #define HAL_HCD_MODULE_ENABLED /* ########################## HSE/HSI Values adaptation ##################### */ /** * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. * This value is used by the RCC HAL module to compute the system frequency * (when HSE is used as system clock source, directly or through the PLL). */ #if !defined (HSE_VALUE) #define HSE_VALUE 25000000U /*!< Value of the External oscillator in Hz */ #endif /* HSE_VALUE */ #if !defined (HSE_STARTUP_TIMEOUT) #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ #endif /* HSE_STARTUP_TIMEOUT */ /** * @brief Internal High Speed oscillator (HSI) value. * This value is used by the RCC HAL module to compute the system frequency * (when HSI is used as system clock source, directly or through the PLL). */ #if !defined (HSI_VALUE) #define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz*/ #endif /* HSI_VALUE */ /** * @brief Internal Low Speed oscillator (LSI) value. */ #if !defined (LSI_VALUE) #define LSI_VALUE 32000U /*!< LSI Typical Value in Hz*/ #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz The real value may vary depending on the variations in voltage and temperature. */ /** * @brief External Low Speed oscillator (LSE) value. */ #if !defined (LSE_VALUE) #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */ #endif /* LSE_VALUE */ #if !defined (LSE_STARTUP_TIMEOUT) #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ #endif /* LSE_STARTUP_TIMEOUT */ /** * @brief External clock source for I2S peripheral * This value is used by the I2S HAL module to compute the I2S clock source * frequency, this source is inserted directly through I2S_CKIN pad. */ #if !defined (EXTERNAL_CLOCK_VALUE) #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the Internal oscillator in Hz*/ #endif /* EXTERNAL_CLOCK_VALUE */ /* Tip: To avoid modifying this file each time you need to use different HSE, === you can define the HSE value in your toolchain compiler preprocessor. */ /* ########################### System Configuration ######################### */ /** * @brief This is the HAL system configuration section */ #define VDD_VALUE 3300U /*!< Value of VDD in mv */ #define TICK_INT_PRIORITY 0x0FU /*!< tick interrupt priority */ #define USE_RTOS 0U #define ART_ACCELERATOR_ENABLE 1U /* To enable instruction cache and prefetch */ #define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ #define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ #define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ #define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ #define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ #define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ #define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ #define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ #define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ #define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ #define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ #define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ #define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ #define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ #define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ #define USE_HAL_JPEG_REGISTER_CALLBACKS 0U /* JPEG register callback disabled */ #define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ #define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ #define USE_HAL_MDIOS_REGISTER_CALLBACKS 0U /* MDIOS register callback disabled */ #define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ #define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ #define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ #define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ #define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ #define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ #define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ #define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ #define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ #define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ #define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ #define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ #define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ #define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ #define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ #define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ #define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ #define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ #define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ /* ########################## Assert Selection ############################## */ /** * @brief Uncomment the line below to expanse the "assert_param" macro in the * HAL drivers code */ /* #define USE_FULL_ASSERT 1U */ /* ################## Ethernet peripheral configuration ##################### */ /* Section 1 : Ethernet peripheral configuration */ /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ #define MAC_ADDR0 2U #define MAC_ADDR1 0U #define MAC_ADDR2 0U #define MAC_ADDR3 0U #define MAC_ADDR4 0U #define MAC_ADDR5 0U /* Definition of the Ethernet driver buffers size and count */ #define ETH_RX_BUF_SIZE 1528U /* ETH Max buffer size for receive */ #define ETH_TX_BUF_SIZE 1528U /* ETH Max buffer size for transmit */ #define ETH_RXBUFNB 5U /* 5 Rx buffers of size ETH_RX_BUF_SIZE */ #define ETH_TXBUFNB 5U /* 5 Tx buffers of size ETH_TX_BUF_SIZE */ /* Section 2: PHY configuration section */ /* LAN8742A PHY Address*/ #define LAN8742A_PHY_ADDRESS 0x00U /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ #define PHY_RESET_DELAY 0x00000FFFU /* PHY Configuration delay */ #define PHY_CONFIG_DELAY 0x00000FFFU #define PHY_READ_TO 0x0000FFFFU #define PHY_WRITE_TO 0x0000FFFFU /* Section 3: Common PHY Registers */ #define PHY_BCR ((uint16_t)0x0000U) /*!< Transceiver Basic Control Register */ #define PHY_BSR ((uint16_t)0x0001U) /*!< Transceiver Basic Status Register */ #define PHY_RESET ((uint16_t)0x8000U) /*!< PHY Reset */ #define PHY_LOOPBACK ((uint16_t)0x4000U) /*!< Select loop-back mode */ #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100U) /*!< Set the full-duplex mode at 100 Mb/s */ #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000U) /*!< Set the half-duplex mode at 100 Mb/s */ #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100U) /*!< Set the full-duplex mode at 10 Mb/s */ #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000U) /*!< Set the half-duplex mode at 10 Mb/s */ #define PHY_AUTONEGOTIATION ((uint16_t)0x1000U) /*!< Enable auto-negotiation function */ #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200U) /*!< Restart auto-negotiation function */ #define PHY_POWERDOWN ((uint16_t)0x0800U) /*!< Select the power down mode */ #define PHY_ISOLATE ((uint16_t)0x0400U) /*!< Isolate PHY from MII */ #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020U) /*!< Auto-Negotiation process completed */ #define PHY_LINKED_STATUS ((uint16_t)0x0004U) /*!< Valid link established */ #define PHY_JABBER_DETECTION ((uint16_t)0x0002U) /*!< Jabber condition detected */ /* Section 4: Extended PHY Registers */ #define PHY_SR ((uint16_t)0x001FU) /*!< PHY special control/ status register Offset */ #define PHY_SPEED_STATUS ((uint16_t)0x0004U) /*!< PHY Speed mask */ #define PHY_DUPLEX_STATUS ((uint16_t)0x0010U) /*!< PHY Duplex mask */ #define PHY_ISFR ((uint16_t)0x1DU) /*!< PHY Interrupt Source Flag register Offset */ #define PHY_ISFR_INT4 ((uint16_t)0x0010U) /*!< PHY Link down inturrupt */ /* ################## SPI peripheral configuration ########################## */ /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver * Activated: CRC code is present inside driver * Deactivated: CRC code cleaned from driver */ #define USE_SPI_CRC 1U /* Includes ------------------------------------------------------------------*/ /** * @brief Include module's header file */ #ifdef HAL_RCC_MODULE_ENABLED #include "stm32f7xx_hal_rcc.h" #endif /* HAL_RCC_MODULE_ENABLED */ #ifdef HAL_EXTI_MODULE_ENABLED #include "stm32f7xx_hal_exti.h" #endif /* HAL_EXTI_MODULE_ENABLED */ #ifdef HAL_GPIO_MODULE_ENABLED #include "stm32f7xx_hal_gpio.h" #endif /* HAL_GPIO_MODULE_ENABLED */ #ifdef HAL_DMA_MODULE_ENABLED #include "stm32f7xx_hal_dma.h" #endif /* HAL_DMA_MODULE_ENABLED */ #ifdef HAL_CORTEX_MODULE_ENABLED #include "stm32f7xx_hal_cortex.h" #endif /* HAL_CORTEX_MODULE_ENABLED */ #ifdef HAL_ADC_MODULE_ENABLED #include "stm32f7xx_hal_adc.h" #endif /* HAL_ADC_MODULE_ENABLED */ #ifdef HAL_CAN_MODULE_ENABLED #include "stm32f7xx_hal_can.h" #endif /* HAL_CAN_MODULE_ENABLED */ #ifdef HAL_CAN_LEGACY_MODULE_ENABLED #include "stm32f7xx_hal_can_legacy.h" #endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ #ifdef HAL_CEC_MODULE_ENABLED #include "stm32f7xx_hal_cec.h" #endif /* HAL_CEC_MODULE_ENABLED */ #ifdef HAL_CRC_MODULE_ENABLED #include "stm32f7xx_hal_crc.h" #endif /* HAL_CRC_MODULE_ENABLED */ #ifdef HAL_CRYP_MODULE_ENABLED #include "stm32f7xx_hal_cryp.h" #endif /* HAL_CRYP_MODULE_ENABLED */ #ifdef HAL_DMA2D_MODULE_ENABLED #include "stm32f7xx_hal_dma2d.h" #endif /* HAL_DMA2D_MODULE_ENABLED */ #ifdef HAL_DAC_MODULE_ENABLED #include "stm32f7xx_hal_dac.h" #endif /* HAL_DAC_MODULE_ENABLED */ #ifdef HAL_DCMI_MODULE_ENABLED #include "stm32f7xx_hal_dcmi.h" #endif /* HAL_DCMI_MODULE_ENABLED */ #ifdef HAL_ETH_MODULE_ENABLED #include "stm32f7xx_hal_eth.h" #endif /* HAL_ETH_MODULE_ENABLED */ #ifdef HAL_FLASH_MODULE_ENABLED #include "stm32f7xx_hal_flash.h" #endif /* HAL_FLASH_MODULE_ENABLED */ #ifdef HAL_SRAM_MODULE_ENABLED #include "stm32f7xx_hal_sram.h" #endif /* HAL_SRAM_MODULE_ENABLED */ #ifdef HAL_NOR_MODULE_ENABLED #include "stm32f7xx_hal_nor.h" #endif /* HAL_NOR_MODULE_ENABLED */ #ifdef HAL_NAND_MODULE_ENABLED #include "stm32f7xx_hal_nand.h" #endif /* HAL_NAND_MODULE_ENABLED */ #ifdef HAL_SDRAM_MODULE_ENABLED #include "stm32f7xx_hal_sdram.h" #endif /* HAL_SDRAM_MODULE_ENABLED */ #ifdef HAL_HASH_MODULE_ENABLED #include "stm32f7xx_hal_hash.h" #endif /* HAL_HASH_MODULE_ENABLED */ #ifdef HAL_I2C_MODULE_ENABLED #include "stm32f7xx_hal_i2c.h" #endif /* HAL_I2C_MODULE_ENABLED */ #ifdef HAL_I2S_MODULE_ENABLED #include "stm32f7xx_hal_i2s.h" #endif /* HAL_I2S_MODULE_ENABLED */ #ifdef HAL_IWDG_MODULE_ENABLED #include "stm32f7xx_hal_iwdg.h" #endif /* HAL_IWDG_MODULE_ENABLED */ #ifdef HAL_LPTIM_MODULE_ENABLED #include "stm32f7xx_hal_lptim.h" #endif /* HAL_LPTIM_MODULE_ENABLED */ #ifdef HAL_LTDC_MODULE_ENABLED #include "stm32f7xx_hal_ltdc.h" #endif /* HAL_LTDC_MODULE_ENABLED */ #ifdef HAL_PWR_MODULE_ENABLED #include "stm32f7xx_hal_pwr.h" #endif /* HAL_PWR_MODULE_ENABLED */ #ifdef HAL_QSPI_MODULE_ENABLED #include "stm32f7xx_hal_qspi.h" #endif /* HAL_QSPI_MODULE_ENABLED */ #ifdef HAL_RNG_MODULE_ENABLED #include "stm32f7xx_hal_rng.h" #endif /* HAL_RNG_MODULE_ENABLED */ #ifdef HAL_RTC_MODULE_ENABLED #include "stm32f7xx_hal_rtc.h" #endif /* HAL_RTC_MODULE_ENABLED */ #ifdef HAL_SAI_MODULE_ENABLED #include "stm32f7xx_hal_sai.h" #endif /* HAL_SAI_MODULE_ENABLED */ #ifdef HAL_SD_MODULE_ENABLED #include "stm32f7xx_hal_sd.h" #endif /* HAL_SD_MODULE_ENABLED */ #ifdef HAL_SPDIFRX_MODULE_ENABLED #include "stm32f7xx_hal_spdifrx.h" #endif /* HAL_SPDIFRX_MODULE_ENABLED */ #ifdef HAL_SPI_MODULE_ENABLED #include "stm32f7xx_hal_spi.h" #endif /* HAL_SPI_MODULE_ENABLED */ #ifdef HAL_TIM_MODULE_ENABLED #include "stm32f7xx_hal_tim.h" #endif /* HAL_TIM_MODULE_ENABLED */ #ifdef HAL_UART_MODULE_ENABLED #include "stm32f7xx_hal_uart.h" #endif /* HAL_UART_MODULE_ENABLED */ #ifdef HAL_USART_MODULE_ENABLED #include "stm32f7xx_hal_usart.h" #endif /* HAL_USART_MODULE_ENABLED */ #ifdef HAL_IRDA_MODULE_ENABLED #include "stm32f7xx_hal_irda.h" #endif /* HAL_IRDA_MODULE_ENABLED */ #ifdef HAL_SMARTCARD_MODULE_ENABLED #include "stm32f7xx_hal_smartcard.h" #endif /* HAL_SMARTCARD_MODULE_ENABLED */ #ifdef HAL_WWDG_MODULE_ENABLED #include "stm32f7xx_hal_wwdg.h" #endif /* HAL_WWDG_MODULE_ENABLED */ #ifdef HAL_PCD_MODULE_ENABLED #include "stm32f7xx_hal_pcd.h" #endif /* HAL_PCD_MODULE_ENABLED */ #ifdef HAL_HCD_MODULE_ENABLED #include "stm32f7xx_hal_hcd.h" #endif /* HAL_HCD_MODULE_ENABLED */ /* Exported macro ------------------------------------------------------------*/ #ifdef USE_FULL_ASSERT /** * @brief The assert_param macro is used for function's parameters check. * @param expr: If expr is false, it calls assert_failed function * which reports the name of the source file and the source * line number of the call that failed. * If expr is true, it returns no value. * @retval None */ #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) /* Exported functions ------------------------------------------------------- */ void assert_failed(uint8_t* file, uint32_t line); #else #define assert_param(expr) ((void)0U) #endif /* USE_FULL_ASSERT */ #ifdef __cplusplus } #endif #endif /* __STM32F7xx_HAL_CONF_H */