92 lines
3.6 KiB
Plaintext
92 lines
3.6 KiB
Plaintext
/**
|
|
@page TIM_PWMInput TIM PWM Input example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
|
* @file TIM/TIM_PWMInput/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the TIM PWM_Input example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
This example shows how to use the TIM peripheral to measure the frequency and
|
|
duty cycle of an external signal.
|
|
|
|
The TIM3CLK frequency is set to SystemCoreClock (Hz), the Prescaler is 0 so the
|
|
counter clock is SystemCoreClock (Hz).
|
|
SystemCoreClock is set to 100 MHz for STM32F412xG Devices.
|
|
|
|
TIM3 is configured in PWM Input Mode: the external signal is connected to
|
|
TIM3 Channel2 used as input pin.
|
|
To measure the frequency and the duty cycle, we use the TIM3 CC2 interrupt request,
|
|
so in the TIM3_CC_IRQHandler routine, the frequency and the duty cycle of the external
|
|
signal are computed.
|
|
|
|
"uwFrequency" variable contains the external signal frequency:
|
|
TIM3 counter clock = SystemCoreClock,
|
|
Frequency = TIM3 counter clock / TIM3_CCR2 in Hz,
|
|
|
|
"uwDutyCycle" variable contains the external signal duty cycle:
|
|
DutyCycle = (TIM3_CCR1*100)/(TIM3_CCR2) in %.
|
|
|
|
The minimum frequency value to measure is (TIM3 counter clock / CCR MAX)
|
|
= (100 MHz)/ 65535
|
|
= 1525 Hz
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Keywords
|
|
|
|
Timers, Input, signals, PWM, External signal, Frequency, Duty cycle, Measure
|
|
|
|
@par Directory contents
|
|
|
|
- TIM/TIM_PWMInput/Inc/stm32f4xx_hal_conf.h HAL configuration file
|
|
- TIM/TIM_PWMInput/Inc/stm32f4xx_it.h Interrupt handlers header file
|
|
- TIM/TIM_PWMInput/Inc/main.h Header for main.c module
|
|
- TIM/TIM_PWMInput/Src/stm32f4xx_it.c Interrupt handlers
|
|
- TIM/TIM_PWMInput/Src/main.c Main program
|
|
- TIM/TIM_PWMInput/Src/stm32f4xx_hal_msp.c HAL MSP file
|
|
- TIM/TIM_PWMInput/Src/system_stm32f4xx.c STM32F4xx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F412xG devices.
|
|
|
|
- This example has been tested with STMicroelectronics STM32412G-DISCOVERY
|
|
board and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
- STM32412G-DISCOVERY Set-up
|
|
- Connect the external signal to measure to the TIM3 CH2 pin (PB.05) (connect to pin 26 in P2 connector).
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
*/
|