97 lines
4.0 KiB
Plaintext
97 lines
4.0 KiB
Plaintext
/**
|
|
@page DMA_FLASHToRAM DMA FLASH To RAM Example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
|
* @file DMA/DMA_FLASHToRAM/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the DMA FLASH to RAM example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
This example provides a description of how to use a DMA to transfer
|
|
a word data buffer from Flash memory to embedded SRAM through
|
|
the HAL API.
|
|
|
|
At the beginning of the main program the HAL_Init() function is called to reset
|
|
all the peripherals, initialize the Flash interface and the systick.
|
|
Then the SystemClock_Config() function is used to configure the system
|
|
clock (SYSCLK) to run at 168 MHz.
|
|
|
|
DMA2 Stream0 channel0 is configured to transfer the contents of a 32-word data
|
|
buffer stored in Flash memory to the reception buffer declared in RAM.
|
|
|
|
The start of transfer is triggered by software. DMA2 Stream0 channel0 memory-to-memory
|
|
transfer is enabled. Source and destination addresses incrementing is also enabled.
|
|
The transfer is started by setting the Channel enable bit for DMA2 Stream0 channel0.
|
|
At the end of the transfer a Transfer Complete interrupt is generated since it
|
|
is enabled and the callback function (customized by user) is called.
|
|
|
|
|
|
STM32 Discovery boards LEDs can be used to monitor the transfer status:
|
|
- LED4 is ON when the transfer is complete (into the Transfer Complete interrupt
|
|
routine).
|
|
- LED5 is ON when there are an error of the transfer (into the Transfer error
|
|
interrupt routine)
|
|
- LED3 is ON when there are an error in the transfer process or in initialisation
|
|
(into the Transfer error interrupt routine)
|
|
|
|
It is possible to select a different Stream and/or channel for the DMA transfer
|
|
example by modifying defines values in the file main.h.
|
|
Note that only DMA2 Streams are able to perform Memory-to-Memory transfers.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Keywords
|
|
|
|
System, DMA, Data Transfer, Memory to memory, Stream, Flash, RAM
|
|
|
|
|
|
@par Directory contents
|
|
|
|
- DMA/DMA_FLASHToRAM/Src/system_stm32f4xx.c STM32F4xx system clock configuration file
|
|
- DMA/DMA_FLASHToRAM/Src/stm32f4xx_it.c Interrupt handlers
|
|
- DMA/DMA_FLASHToRAM/Src/main.c Main program
|
|
- DMA/DMA_FLASHToRAM/Inc/stm32f4xx_hal_conf.h HAL Configuration file
|
|
- DMA/DMA_FLASHToRAM/Inc/stm32f4xx_it.h Interrupt handlers header file
|
|
- DMA/DMA_FLASHToRAM/Inc/main.h Main program header file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F407xx devices.
|
|
|
|
- This example has been tested with STMicroelectronics STM32F4-Discovery RevB & RevC
|
|
boards and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
*/
|